Kit, body to frame pad.
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Bushing and bracket kit, front stabilizer bar. Includes: Two (2) each of #5492 and 5476, four (4) each of #5493 and attaching parts.
Door edge weatherstrip. This part is the primary door to body weatherstrip.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Weatherstrip, door. Installs on inner dog leg.
Deflector, rear stone. Rubber. Installs between body and rear bumper. Includes fasteners.
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Channel, flexible door window run. Stainless steel beaded. Available in 5ft lengths.
Mount, front motor. Two (2) required per car.
Window-felt kit, quarter window. Right side only.
Window-felt kit, quarter window. Left side only.
Bushings, stabilizer bar to frame. Four (4) piece set.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pair.
Seals, air vent inlet duct to heater outside.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Shackle kit, front of rear spring. Kit completes one spring.
Tube, windshield cowl drain.
Seal, front fender splash apron to frame.
Kit, taillight mounting pad. Fin and Oval type. Six (6) piece set.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Seals, air vent damper rubber.
Bushing, brake master cylinder. Installs on push rod.
This Transmission Mount is designed from the original part for a correct fitment. Mounts at the rear of manual and automatic transmissions.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
This Fender Skirt Edge Seal pair is designed from the original part for superior fitment and seal. For original skirts only this seal fits between fender skirt and rear fender body.
Bolt and bushing kit, rear of rear spring shackle. Enough for one (1) side only.
Bumper, front suspension lower arm.
Insulator, transmission gear shift column lever.
Insulator, gear shift.
Set, spring clamp liner. Front spring takes eight pieces for both sides Rear spring takes four pieces for both sides. Six (6) piece set.
Seal, steering column tube. Installs on top of floor mat.
Seal, front fender splash apron to fender anti-squeak. Seventy two (72) inch strip.
Seal, steering column to floor. Installs under floor mat.
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Bumpers, top of cowl to hood.
Kit, cowl lacing. Rubber.
Pad, brake and clutch pedal. Replacement type.
Seals, ventilator air inlet duct door to duct inside.
Pad, rear mount antenna.
Seal, garnish molding to dash rubber. Eighty four (84) inches long. Replaces factory #B7A-7003127-E.
Seals, cowl top ventilator grille anti-squeak. U-shaped.
Pads or gaskets for the outside door handles. Front or rear, this is a four (4) piece set.
Weatherstrip, sash channel. Thirty one and one half (31-1/2) inch long rubber piece that goes between glass and sash channel.
Gaskets, taillight lens to housing. Four (4) piece set.
Seal, garnish molding to dash rubber. Forty six (46) inches long. Models WITH A/C. Replaces factory #B7A-7003127-B.
Pad, brake and clutch pedal. Slip over type.