Please click on the part name in red in order to get a complete description.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Fully molded rubber ends.
Side window horizontal seal (also known as beltline weatherstrip). These strips wipe the side windows when the glass is lowered.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Side window vertical leading edge weatherstrip.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Channel, door glass run. Lock side. Rear of front door. Your original brackets attach to this.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Mount, front motor. Two (2) required per car.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Kit, taillight mounting pad. Fin and Oval type. Six (6) piece set.
Seals, dash bezel. Five (5) piece set.
Seal, fender skirt.
Seal, vent window upper tip at door window post.
Bushing, brake master cylinder. Installs on push rod.
Bushing, control arm. Upper inner. Two (2) required per side.
Gaskets, taillight lens to housing. Four (4) piece set.
Pads, outside door handle. Four (4) piece set.
Repair kit, stabilizer bar end. Two (2) kits required per car.
Insulator, transmission gear shift column lever.
Bushing, control arm. Two (2) required per side.
Grommet, fuel filler neck. Fully molded flexible rubber. Four inch (4") outside diameter by two and one eighth inch (2-1/8") inside diameter by one half inch (1/2") height.
Kit, cowl lacing.1957-60: Mercury with Reverse Hood; 1958: Edsels; 1958-60: Thunderbird.
Pad, rear mount antenna.
Gaskets, parking light lens.
Pads, parking light body to fender.
Pad, brake and clutch pedal. Slip over type.
Bumper, on lower door and/or fuel filler cover. Type with threaded end.
Insulator, front coil spring.
Pad, front fender mount antenna.
Gasket, headlight bulb bucket to fender.
Grommet, antenna lead-in. For front mount type.
Anti-rattler, trunk torsion bar.
Seal, idler arm. Two (2) required per car.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Grommet, fuel tank vent pipe to body.
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Seal, accelerator pedal rod to floor.
Bumper, brake and clutch pedal arm.
Bumpers, ashtray door or glove box door.
Pads, back center of front fender. Mounts where fender bolts to cowl.
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Bumper, hood pull cam. Two (2) required per car.Ford Cars 1957-60 Bumper, hood pull cam. 2 required per car. Ford Cars 1958-59 Bumper, trunk lid.
Gasket, outside mirror. Paper.
Bushing, shock absorber link. May be used for front or rear spring.Chrysler 1951-54 Bushing, rubber, shock absorber link.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Plug, brake adjustment hole. Fits five sixteenths (5/16) inch by one (1) inch slot. Most models with drum brakes.Length: 1.25 inches. Height: .875 inches.
Seal, clutch pedal rod to firewall.
Tip, sun visor arm boot. Used where sun visor hooks to clip in center. Two (2) required per car.