This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Weatherstrip, large rear side window glass perimeter. Fully molded with factory type extrusion and corners.
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes fasteners and clips for easy installation.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Harmonic Balancer - Revulcanization service only. Send in core and allow three weeks for service.
These Engine Support Mounts pair are fully molded to heavy steel cores as original. The supports are for the rear right and left engine mounts for models with Hydramatic transmission.
Mounting Assembly, engine to frame, front lower. Revulcanization service only.Length: 4.50 inches.
Motor mount, upper, engine bracket at front cross member. One (1) per vehicle. Revulcanization service only.Length: 6.1875 inches. Width: 2.875 inches.
Insulator, engine mount, front lower. Revulcanization service only.Length: 5.125 inches.
Insulator, drive shaft support, center, molded rubber on heavy steel core. Note: Not used on models with Air Ride suspension.
Bumper, upper division post.Length: 1.5 inches. Width: .5625 inches.
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Rear door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core. For rear doors.
Weatherstrip, front door, auxiliary on body above beltline, hinge pillar windshield post. Two (2) strips, each thirteen and three eighths (13-3/8) inches long with retaining clips.
Weatherstrip, front door auxiliary, on door at beltline, right and left. Uses snap-in fasteners, four (4) each included.
Bumpers, front wheel upper control arm.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Front door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core. For front doors.
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Seal, headlight outer rim to sealed beam retainer ring. Possible fit for models with dual headlights.Width: .375 inches. Height: .9375 inches.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Steele Rubber Products has the best quality Fenderskirt edge seal for your Street Rod or Custom Build project. Made from top-quality rubber to ensure durability and proper seal.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Pads, brake and clutch pedal. Two (2) per car. Length: 4.0 inches. Width: 2.5 inches.
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Cover, rocker panel inner dust shield. Fully molded with proper attaching teeth and flap.
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Grommet, glove box door cushion. One and three quarters long (1-3/4") and thirteen sixteenths (13/16")wide.Length: 1.75 inches. Width: .8125 inches.
Bumper, hood side to fender ledge. Six (6) used per car.Length: 1.25 inches. Width: .875 inches.
Bumper, tailgate support. Two (2) bumpers mount on tailgate and two (2) mount on body in lower sections. Four (4) required.
Grommet, dimmer switch for carpet application.
Isolator, body mounting. Fully molded rubber. Two inches (2") outside diameter by seven eighths inch (7/8") inside hole diameter by three fourths inch (3/4") height.
Wedge, tailgate bumper anti-rattler. Mounts on both end jamb areas on tailgate.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Bumper, window stop. One and one fourth (1-1/4) inch square by one half (1/2) inch thick. Compare with our #33-0540-62 and #33-0675-62.
Bushing, spring and shackle, rear.
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Dust cover, tie rod ends.
Pad, for each body bolt under frame bracket, to cushion washer and nut. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by seven eighths inch (7/8") inside hole diameter by nine sixteenths inch (9/16) height.
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
This is the knob or button for the inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. The part fits many different vehicles.
Grommet, shock and stabilizer link. Eight (8) required per car. Fully molded rubber with locating collar. One and one sixteenth inch (1 1/16") outside diameter by nine sixteenths inch (9/16") locating collar outside diameter by three eighths inch (3/8") i
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available. Available by the foot.
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.