This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This Revulcanization Service Only is designed to restore your Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Hardtop roof rail weatherstrip (6 window). This part fits on the roof of the vehicle and seals the side window when the window is fully raised. Note: this is for 6 window 4dr hardtops only (vehicles with rear quarter windows). See part #70-
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Weatherstrip, fixed quarter window.Width: 20.5 inches. Height: 10.25 inches.
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Fitted gasket provides a formed, seamless seal.
This rear door weatherstrip is designed from the original part for superior fitment and seal. This seal mounts around the front, bottom, and rear of the door using pre-installed clips.
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes 6 clips for easy installation. Made of top quality rubber.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Transmission mount. Revulcanization service only.Length: 8.0 inches. Width: 3.0625 inches.
Weatherstrip, upper vertical on rear body lock pillar, eleven (11) inches long brass core, cloth facing. Right and Left.Length: 11.0 inches.
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Rear door hinge pillar seal. This part seals the bottom of the rear door side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core.
Rear door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core. For rear doors.
Weatherstrip, front door opening. Auxiliary on door hinge pillar at beltline, right and left. Sometimes called "L" or "J" strips. Fully molded with authentic configuration to help guide water to the outside of vehicle. Set includes four (4) button-type fa
Front door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction. Note: order #60-0591-79 rear door u-jamb seals separately.
Bumper, side window glass.
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Insulator, engine support at transmission. Revulcanization service only.Length: 7.375 inches. Width: 1.75 inches. Height: 1.5 inches.
Weatherstrip, rear bumper to body. Two, thirty two (32) inch pieces.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Side window vertical leading edge weatherstrip.
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This 48” long x 1-1/8” wide weatherstrip provides complete coverage.
Wiper Transmission Gasket - This is the seal for the wiper motor crank. For two (2) speed wiper motors only. These parts are made of the highest quality and authenticity. Replaces # 4906021.
This Radiator Mounting Pad is designed from the original part for superior fitment and function. This mounting isolator pad fits to the radiator support pan. Made with molded-in metal washer like original.
Bumper, fuel filler door.Length: 5.4375 inches. Width: .75 inches.
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable, measures one and one eighth inch (1 1/8") long when removed. Part dimensions with metal sleeve inserted are: One and seven eighths inch (1 7/8")
This black rubber Battery Clamp Cover helps to protect the nearby metal and finish. Good copy from an original part. Length: 3-1/2" inches.
Pad, body mounting. Rubber with metal nut and washer molded in. One and seven eighths inch (1 7/8") outside diameter by thirteen sixteenths inch (13/16") nut outside length by seven sixteenths inch (7/16") inside hole diameter. Three fourths inch (3/4") c
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. One and three fourths inch (1 3/4") outside diameter by one inch (1") inside diameter with one half inch (1/2") hole through center of retaining washer that is molded in by seven e
Spring Insulator, rear
Grommet, antenna lead through sheet metal.
Steele Rubber Products offers the best quality Dimmer Switch Grommet for your classic vehicle. This universal fit dimmer switch grommet is used during carpet installations in automotive restorations. Includes a wide flange for floor dimmer switch fitments.
Isolator, body mounting. Fully molded rubber. Two inches (2") outside diameter by seven eighths inch (7/8") inside hole diameter by three fourths inch (3/4") height.
This Masticated Rubber Sheet is three thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Bumper, hood to fender ledge. Number required varies. Molded rubber type.Width: 1.5 inches. Height: 1.0 inches.
Bumper, adjustable type, hood front. Cadmium plated bolt (5/16)-18 x 1-1/4", rubber bumper 1-1/8" in diameter, 5/8" thick.Height: 1.875 inches.