Search Results
Body Weatherstrip Kit
p/n: 90-3146-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Rear Window Gasket
p/n: 60-0553-81
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Hardtop Roof Rail Weatherstrip
p/n: 70-0710-68
Hardtop roof rail weatherstrip. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
Motor mount service
p/n: 70-1774-11
Motor mount. Revulcanization service only. Center holes measure two and seven eighths (2-7/8) inches apart.Length: 5.375 inches.
Front Door Vent Window Set
p/n: 90-0410-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Rear Door Weatherstrip
p/n: 60-0592-72
This rear door weatherstrip is designed from the original part for superior fitment and seal. This seal mounts around the front, bottom, and rear of the door using pre-installed clips.
Front Door Weatherstrip
p/n: 60-0590-72
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes 6 pins for easy installation. Made of top quality rubber.
Windshield Gasket
p/n: 70-0671-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Transmission mount service
p/n: 50-0429-25
Transmission mount. Revulcanization service only.Length: 8.0 inches. Width: 3.0625 inches.
Front Door Vent Window Weatherstrips
p/n: 38-0071-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Transmission mount service
p/n: 50-0264-25
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Support arm bumper
p/n: 50-0526-32
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Front Inner Fender / Splash Apron Seal Set
p/n: 70-4055-45
This complete twelve (12) piece Front Inner Fender / Splash Apron Seal set is designed from the original part for superior fitment and seal. Made from original fabric reinforced masticated rubber to ensure durability and proper function. Left and Right precision die cut pieces attach to front inner fender panels.
Rear Door Hinge Pillar Filler
p/n: 60-0591-79
Rear door hinge pillar seal. This part seals the bottom of the rear door side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core.
Door weatherstrip hinge pillar
p/n: 60-0326-73
Weatherstrip, front door opening. Auxiliary on door hinge pillar at beltline, right and left. Sometimes called "L" or "J" strips. Fully molded with authentic configuration to help guide water to the outside of vehicle. Set includes four (4) button-type fa
Front door lock pillar filler
p/n: 70-0941-79
Front door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction. Note: order #60-0591-79 rear door u-jamb seals separately.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Transmission mount service
p/n: 50-0186-25
Insulator, engine support at transmission. Revulcanization service only.Length: 7.375 inches. Width: 1.75 inches. Height: 1.5 inches.
Side Window Vertical Leading Edge
p/n: 70-1271-80
This Side Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Rear bumper weatherstrip
p/n: 70-1581-30
Weatherstrip, rear bumper to body. Two, thirty two (32) inch pieces.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Beltline Weatherstrip
p/n: 70-0651-58
Rigid, rubber covered weatherstrip with flock lining and one fourth (1/4) inch chrome edge. Available in a 6ft piece.
Vent division bar weatherstrip
p/n: 60-0636-56
Front vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. See Front door vent weatherstrip for main rubber seal.
Front Coil Spring Pad
p/n: 50-0476-35
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Side Window Sash Channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Rigid Run Channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Trunk Weatherstrip
p/n: 70-0773-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Wiper Transmission Gasket
p/n: 60-0593-53
Wiper Transmission Gasket - This is the seal for the wiper motor crank. For two (2) speed wiper motors only. These parts are made of the highest quality and authenticity. Replaces # 4906021.
Radiator Mounting Pad
p/n: 50-0529-31
This Radiator Mounting Pad is designed from the original part for superior fitment and function. This mounting isolator pad fits to the radiator support pan. Made with molded-in metal washer like original.
Door handle gasket kit
p/n: 70-0925-69
Gasket set, outside door handle. Die cut rubber construction. Six (6) piece set for two (2) handles.
Body mounting pad
p/n: 50-0506-48
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable, measures one and one eighth inch (1 1/8") long when removed. Part dimensions with metal sleeve inserted are: One and seven eighths inch (1 7/8")
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Body mounting pad
p/n: 50-0508-48
Pad, body mounting. Rubber with metal nut and washer molded in. One and seven eighths inch (1 7/8") outside diameter by thirteen sixteenths inch (13/16") nut outside length by seven sixteenths inch (7/16") inside hole diameter. Three fourths inch (3/4") c
Body mounting pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. One and three fourths inch (1 3/4") outside diameter by one inch (1") inside diameter with one half inch (1/2") hole through center of retaining washer that is molded in by seven e
Body Mount Isolator
p/n: 50-0507-48
Isolator, body mounting. Fully molded rubber. Two inches (2") outside diameter by seven eighths inch (7/8") inside hole diameter by three fourths inch (3/4") height.
Masticated Rubber Sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Strut rod bushing
p/n: 50-0522-27
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Hood bumper
p/n: 50-0489-42
Bumper, hood to fender ledge. Number required varies. Molded rubber type.Width: 1.5 inches. Height: 1.0 inches.
Hood bumper
p/n: 50-0205-42
Bumper, adjustable type, hood front. Cadmium plated bolt (5/16)-18 x 1-1/4", rubber bumper 1-1/8" in diameter, 5/8" thick.Height: 1.875 inches.
Glovebox Link Bumper
p/n: 50-0367-88
Bumper, glove box check link. Fits on glove box door arm as needed.Length: .75 inches. Width: .5625 inches. Height: .3125 inches.
Window Stop Stem Bumper
p/n: 33-0540-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.