This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Door edge weatherstrip with molded corners. This part is the primary door to body weatherstrip. Includes pins and clips for easy installation. Also includes 26 sockets.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Weatherstrip, rear quarter stationary vent window. This gasket is for the triangular window just behind the rear door on four (4) door post sedans.
Transmission mount. Revulcanization service only.Length: 8.0 inches. Width: 3.0625 inches.
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Gutter, cowl side drain, left and right. Rubber with metal core as original. Eleven (11") inches long.Length: 11.0 inches.
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
This comprehensive ten (10) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right made pieces fit over suspension a-arms and inside front inner fenders.
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Bushing, track bar. Molded out of BUNA rubber with correct metal sleeve like original.Height: 1.875 inches.
Weatherstrip, front door opening. Auxiliary on door hinge pillar at beltline, right and left. Sometimes called "L" or "J" strips. Fully molded with authentic configuration to help guide water to the outside of vehicle. Set includes four (4) button-type fa
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Gasket, taillight lens. Made of die cut sponge rubber to original configuration.
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
This two (2) piece Rear Bumper Gravel and Splash Guard Shield pair is designed from the original part for superior fitment and seal. Twenty-two (22) inches long per side.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This 48” long x 1-1/8” wide weatherstrip provides complete coverage.
Grommet, firewall, for heater control cabled wiring harness.Width: 2.875 inches. Height: 1.5625 inches.
Bumper, fuel filler door.Length: 5.4375 inches. Width: .75 inches.
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable, measures one and one eighth inch (1 1/8") long when removed. Part dimensions with metal sleeve inserted are: One and seven eighths inch (1 7/8")
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Pad, body mounting. Rubber with metal nut and washer molded in. One and seven eighths inch (1 7/8") outside diameter by thirteen sixteenths inch (13/16") nut outside length by seven sixteenths inch (7/16") inside hole diameter. Three fourths inch (3/4") c
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens & taillight housing.
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. One and three fourths inch (1 3/4") outside diameter by one inch (1") inside diameter with one half inch (1/2") hole through center of retaining washer that is molded in by seven e
Spring Insulator, rear
Grommet, antenna lead through sheet metal.
Grommet, dimmer switch for carpet application.
Isolator, body mounting. Fully molded rubber. Two inches (2") outside diameter by seven eighths inch (7/8") inside hole diameter by three fourths inch (3/4") height.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Bumper, hood to fender ledge. Number required varies. Molded rubber type.Width: 1.5 inches. Height: 1.0 inches.
Bumper, adjustable type, hood front. Cadmium plated bolt (5/16)-18 x 1-1/4", rubber bumper 1-1/8" in diameter, 5/8" thick.Height: 1.875 inches.
Bumper, glove box check link. Fits on glove box door arm as needed.Length: .75 inches. Width: .5625 inches. Height: .3125 inches.
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Dust cover, tie rod ends.
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Bumper, hood to fender. Extruded rubber type.Width: .75 inches. Height: 1.0 inches.