This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
This Spring Shackle Bushing Set is for the rear of rear leaf spring. This set is made with original style rubber bushings. Two (2) sets are required per car.
This Rear Bumper Stone Deflector is an exact reproduction of the original rear bumper to body seal. This seal is used to keep road debris from coming up and damaging your vehicle.
Bushings, stabilizer bar to frame. Four (4) piece set.
This Trunk Lid Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Front vent window division post seal. Fully molded with metal core and pre drilled holes.
Side window vertical leading edge weatherstrip.
Mount, front motor. Two (2) required per car.
This manual Transmission Mount is designed from the original part for superior fitment and seal. This rear mount fits between the transmission and the crossmember to locate and retain the rear of the engine / transmission powertrain.
Channel, lower door glass run. Lock side.
This Spring Shackle Bushing Set is an original style rubber leaf spring bushing used on the front of rear spring. One (1) set is required per spring.
Pad, brake and clutch pedal. Slip over type. Automatic transmission and manual brakes.
This six (6) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Bumpers, upper door glass division post.
Mount, motor support, front.
This Transmission Mount is designed from the original part for a correct fitment. Mounts at the rear of manual and automatic transmissions.
Bumper, front suspension lower arm.
Seal, radiator support top to hood. Includes special plastic buttons to install. For models with A/C.
Bumpers, hood front to radiator support. Five sixteenths (5/16) inch by twenty four (24) thread.
Bumpers, hood on Fender. Four (4) piece set.
Insulator, gear shift.
This Splash Apron mounts between the front fender splash apron and the front fender. The seal is an exact reproduction of the original Ford part. Sold as a seventy-two (72) inch strip.
Pads, taillight rim to housing.
Gaskets, taillight housing to body.
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Pad, parking brake pedal. Slip over type.
Bushing, rear spring front rubber. Two (2) required per spring.
This eleven (11) piece Front Stabilizer Bar End Link Kit is designed from original parts so it fits correctly. Two (2) kits / sets required per car as one (1) kit / set services one side of front stabilizer bar.
Pad, brake and clutch pedal. Slip over type.
Bumper, rear spring and axle. 1957-59: Full size Fords: Five (5) required per car (1 in center, 2 each side).
Bumpers, door. Seven sixteenths (7/16) inch high. Fits on door jamb where rear of door closes against body and on rear lower part of door.
Bumpers, door. Five eighths (5/8) inch high. Installs on door jamb where rear of door closes against body and on rear lower part of door.
Insulator, front coil spring.
Seal, right front fender apron to frame. Includes staples for installation.
This Shifter Bushing Set is designed from the original part for superior fitment and function. This bushing set will restore and tighten that loose and sloppy column shift gear selector to a like new condition.
Gaskets, parking light lens.
Grommet, antenna lead-in. For front mount type.
This Rear Spring Pad is used as a spring insert silencer. The leaf spring insulator installs between the leaves.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glove box doors.
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.