This is a Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This eight (8) piece anti-rattle set includes inner and outer window felt beltline weatherstrips for each side and quarter window.
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Fully molded rubber ends.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Side window vertical leading edge weatherstrip.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Mount, front motor. Two (2) required per car.
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
This Spring Shackle Bushing Set is for the front of the rear leaf spring. One (1) set completes one spring.
Pad, brake and clutch pedal. Slip over type. Automatic transmission and manual brakes.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Seal, fender skirt.
Seal, vent window upper tip at door window post.
Bushing, control arm. Upper inner. Two (2) required per side.
This Spring Shackle Bushing Set is for the rear of the rear leaf spring on car models and the front of the front leaf spring on truck models. Two (2) sets needed per vehicle.
Bumper, front suspension lower arm.
Gaskets, taillight lens to housing. Six (6) piece set.
Pads, outside door handle. Four (4) piece set.
This eleven (11) piece Stabilizer Bar End Repair Set is designed to withstand harsh conditions without deteriorating. Two (2) sets required per car.
Insulator, gear shift.
Six (6) piece Spring Clamp Liner Set. The front spring takes eight pieces for both sides and the rear spring takes four pieces for both sides.
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Grommet, fuel filler neck. Fully molded flexible rubber. Four inch (4") outside diameter by two and one eighth inch (2-1/8") inside diameter by one half inch (1/2") height.
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An reproduction using the correct profile dense rubber extrusion.
Pad, rear mount antenna.
Pad, parking brake pedal. Slip over type.
Gaskets, parking light lens.
Pads, parking light body to fender.
Pad, brake and clutch pedal. Slip over type.
Bumper, rear spring and axle. 1957-59: Full size Fords: Five (5) required per car (1 in center, 2 each side).
Bumper, on lower door and/or fuel filler cover. Type with threaded end.
Insulator, front coil spring.
Pad, front fender mount antenna.
Gasket, headlight bulb bucket to fender.
Grommet, antenna lead-in. For front mount type.
This Rear Spring Pad is used as a spring insert silencer. The leaf spring insulator installs between the leaves.
Cork sash channel filler. Available by the foot.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Seal, accelerator pedal rod to floor.
Bumper, brake and clutch pedal arm.
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glove box doors.
Bushing, door hinge.
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Bumper, hood pull cam. Two (2) required per car.Ford Cars 1957-60 Bumper, hood pull cam. 2 required per car. Ford Cars 1958-59 Bumper, trunk lid.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Tip, sun visor arm boot. Used where sun visor hooks to clip in center. Two (2) required per car.