Search Results
Front Door Vent Window Set
p/n: 90-0436-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Motor Mount Revulcanizing Service
p/n: 70-0548-11
This Front Motor Mount revulcanizing service replaces the rubber in your original Motor Mounts to make them like new again. The process is designed for the original factory mounts only. Send in cores and allow three weeks for service.
Front Door Vent Window Weatherstrips
p/n: 38-0103-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Windshield Gasket
p/n: 70-1005-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Prop shaft support service
p/n: 70-0748-27
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
Motor mount service
p/n: 70-0629-11
Cushion support, motor, rear on transmission to cross member. Revulcanization service only. Similar to #70-0674-11.Length: 3.75 inches. Width: 2.25 inches.
Cadillac Master Parts List 1957 - 1964 (Reprint)
p/n: 07-1443-07
This 1957-1964 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems.
Cowl drain gutter
p/n: 70-0867-73
Gutter, cowl side drain, left and right. Rubber with metal core as original. Eleven (11") inches long.Length: 11.0 inches.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-2495-45
This fourteen (14) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Defroster Vent Gasket
p/n: 70-2279-31
Gasket, defroster vent at base of windshield. One (1) pair required per car.
Fenderskirt Edge Seal
p/n: 70-0154-45
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Hood To Cowl Weatherstrip
p/n: 70-1019-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Axle rebound pad
p/n: 70-2225-32
Bumper, rear spring axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.Width: 1.9375 inches. Height: 2.
Beltline Weatherstrips
p/n: 70-1121-61
These Beltline Weatherstrips (sometimes called "scraper seal") come in a three (3) foot pair. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 3ft pair.
Door weatherstrip hinge pillar
p/n: 60-0326-73
Weatherstrip, front door opening. Auxiliary on door hinge pillar at beltline, right and left. Sometimes called "L" or "J" strips. Fully molded with authentic configuration to help guide water to the outside of vehicle. Set includes four (4) button-type fa
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Beltline Weatherstrip
p/n: 70-1120-61
This Beltline Weatherstrip comes in a six (6) foot length for the outer beltline (sometimes called "scraper seal"). For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 6ft lengths.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Front Stabilizer Bar End Link Kit
p/n: 70-2110-33
Kit, front stabilizer bar link assembly replacement. Twenty-two (22) piece set. One (1) kit for both sides of one (1) car. Hex head bolt. 5/16"-18nc x 6-15/16" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Vent division bar weatherstrip
p/n: 70-1014-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Radiator Upper Support Filler
p/n: 70-2502-45
This single piece Radiator Upper Support Filler is designed from the original part for superior fitment and function. Filler piece is die cut from quality masticated rubber to authentic original dimensions. Fits at radiator to radiator upper support.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Wiper Transmission Gasket
p/n: 60-0593-53
Wiper Transmission Gasket - This is the seal for the wiper motor crank. For two (2) speed wiper motors only. These parts are made of the highest quality and authenticity. Replaces # 4906021.
Radiator mounting pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Auxiliary / Frame Dust Shield
p/n: 70-3084-45
This Auxiliary / Frame Dust Shield pair is designed from the original part for superior fitment and function. The two (2) shield pieces are die cut from quality masticated rubber to authentic original dimensions. These shield pieces fit under the vehicle sway bar, near the frame.
Metal sleeved grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Door Handle Gasket Set
p/n: 70-0925-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Taillight Lens Gaskets - In Fin
p/n: 70-3502-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the taillight lens & taillight housing in fin.
Back Up Light Lens Gaskets
p/n: 70-3234-17
This Back Up Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the back-up light lens and the back-up light housing or light bezel.
Directional & Parking Light Lens Gaskets
p/n: 70-3115-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Taillight Lens Gaskets
p/n: 70-3235-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
Battery Clamp Cover
p/n: 70-0095-21
This black rubber Battery Clamp Cover helps to protect the nearby metal and finish. Good copy from an original part. Length: 3-1/2" inches.
Headlight Bucket to Fender Seals
p/n: 70-3085-14
This two (2) piece Headlight Bucket to Fender Seal pair is designed from the original part for superior fitment and seal. Die cut from original style masticated rubber for a like factory fit.
Hood bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Plastic guide plate
p/n: 50-0384-62
Guide plate, plastic, attaches to various outer scraper weatherstrips.
Hood bumper
p/n: 70-0907-42
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Dimmer Switch Grommet
p/n: 40-0083-88
Steele Rubber Products offers the best quality Dimmer Switch Grommet for your classic vehicle. This universal fit dimmer switch grommet is used during carpet installations in automotive restorations. Includes a wide flange for floor dimmer switch fitments.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Body Mount Isolator
p/n: 70-2232-48
Isolator, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body mounting pad
p/n: 70-2233-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body mounting pad
p/n: 70-2234-48
Pad, body mounting to chassis. Fully molded rubber, square type. Six (6) or more are used per car. Two and three sixteenths inch (2 3/16") square by three fourths inch (3/4") inside diameter hole by one half inch (1/2") inch height.
Plastic guide plate
p/n: 50-0385-58
Plastic guide plate, attaches to various outer scraper weatherstrips.Length: 1.625 inches. Width: .625 inches.
Rear View Mirror Mounting Pad
p/n: 70-3083-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) door mounted rear view mirror.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.