Original equipment style side window horizontal seal (also known as beltline weatherstrip). These strips wipe the side windows when the glass is lowered.
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Made from Standard material. Side window horizontal seal (also known as beltline weatherstrip). These strips wipe the side windows when the glass is lowered.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This Front Door Weatherstrip pair is designed from the original parts for superior fitment and seal. These primary door seals mount (glue-on) directly to the left and right doors sealing the full perimeter of the doors against the vehicle body when the door is closed.
Seal, rear bumper to body. Splash apron. Three (3) piece kit includes: left, right and special molded center piece.
This Front Coil Spring Saddle Insulator Kit is a four (4) piece kit with two front coil spring bushings and two spring insulators to restore the performance of your classic vehicle.
Insulator, cantilever spring type rear support.
Bumper, tailgate. Installs on body. From 5-01-1963 thru 1965.
This Tailgate Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the vehicle body to support / cushion the tailgate closure. Includes right and left bumpers & corresponding attaching screws.
Tailgate glass to roof side seal. Vertical seal on body between tailgate glass and roof side.
Shackle kit, rear of rear spring. Two (2) kits required per car.
Shield, generator splash.
Bumpers, side of hood to fender. Four (4) piece set.
Seals, windshield drain trough. For A-pillar
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Seal, steering tube to floor. Used on top of floor mat.
Pads, taillight housing to body.
This Firewall To Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Weatherstrip, tailgate lower glass sash channel. Goes between glass and channel.
Bumpers, hood front to radiator support. Five sixteenths (5/16) inch by twenty four (24) thread.
Seal, radiator support to hood. Includes staples to install.1960-62: All Falcon models; 1963: Falcon 6 cylinder models EXCEPT those with air conditioner.
Insulator, gear shift.
Bumpers, seat back for second seat.
Lacing, hood cowl.
Bumpers, rear of hood to top of fender. Two (2) required per vehicle.Ford Cars 1961-64 Bumpers, rear of hood to top of fender. Requires 2 pair for hood.
Gaskets, parking light lens.
This eleven (11) piece Front Stabilizer Bar End Link Kit is designed from original parts so it fits correctly. Two (2) kits / sets required per car as one (1) kit / set services one side of front stabilizer bar.
Pads, outside door handle.
Pad, brake and clutch pedal. Slip over type.
Bumpers, door. Seven sixteenths (7/16) inch high. Fits on door jamb where rear of door closes against body and on rear lower part of door.
Bumpers, door. Five eighths (5/8) inch high. Installs on door jamb where rear of door closes against body and on rear lower part of door.
Upper Control Arm Bumper made with top quality rubber. Includes nut.
This Shifter Bushing Set is designed from the original part for superior fitment and function. This bushing set will restore and tighten that loose and sloppy column shift gear selector to a like new condition.
Gasket, headlight bucket to fender.
Grommet, antenna lead-in. For front mount type.
Gaskets, wiper pivot bezel to cowl.
Bumpers, glovebox and/or fuel filler door. Used as glove box door bumpers for all models listed, used as fuel door bumper for 1950-51 cars and 57-59 retractables only.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Seal, accelerator pedal linkage to firewall.
Bumper, brake and clutch pedal arm.
Bumpers, ashtray door or glove box door.
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Bumper, fuel tank filler lid. Gray rubber.Ford Cars 1960-63 Bumper, license plate rubber. Used on rear bumper. 2 required per car.
Plug, brake adjustment hole. Fits five sixteenths (5/16) inch by one (1) inch slot. Most models with drum brakes.Length: 1.25 inches. Height: .875 inches.