Prop shaft support service
p/n: 70-0748-27
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
Splash Apron / A-Arm Dust Shield Set
p/n: 70-2496-45
This ten (10) piece Splash Apron / A-Arm Dust Shield set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Axle Rebound Pad
p/n: 70-2225-32
Bumper, rear spring axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Headlight & Cornering Light Filler Seal Set
p/n: 70-2788-14
This six (6) piece Headlight & Cornering Light Filler Seal Set is designed from the original part for superior fitment and seal. These pieces fit behind the cornering lights.
Wiper Transmission Gasket
p/n: 60-0593-53
Wiper Transmission Gasket - This is the seal for the wiper motor crank. For two (2) speed wiper motors only. These parts are made of the highest quality and authenticity. Replaces # 4906021.
Hood to Fan Shroud Seal
p/n: 70-2789-43
This Hood To Fan Shroud Seal is designed from the original part for superior fitment and function. Attaches to bottom side of hood. This seal piece is die cut from quality masticated black rubber to authentic original dimensions.
Front Stabilizer Bar End Link Set
p/n: 70-2110-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Body / Cowl to Fender Seals
p/n: 70-2790-43
This Body / Cowl to Fender Seals pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
AC Condenser Mount
p/n: 70-0964-31
Mount, air conditioning condenser. Four (4) used per car.Length: 1.0 inches. Width: .75 inches.
Cornering Light Lens Gaskets
p/n: 70-3098-17
This Cornering Light Lens Gasket pair is designed from the original part for superior fitment and seal. These quality reproduction gaskets fit between the cornering light lens and the cornering light housing or bezel.
Directional and Parking Light Lens Gaskets
p/n: 70-3095-16
This Directional Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Taillight Lens Gaskets - In Bumper
p/n: 70-3089-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the outer taillight lens & taillight housing in bumper.
Hood Bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Hood Bumper
p/n: 70-0907-42
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Body Mount Isolator
p/n: 70-2232-48
Isolator, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mounting Pad
p/n: 70-2233-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.