Please click on the part name in red in order to get a complete description.
This ten (10) piece kit includes the major weatherstrip components needed for your restoration project. These parts are designed from factory originals with fully molded corners and end pieces for superior performance and a factory fit.
Hardtop roof rail weatherstrip. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These door weatherstrips are designed from the original parts for a superior fitment and seal. They are made with brass cores inside of the molded ends for a factory look and fit and an extra-long life.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Made from Standard material. Side window horizontal seal (also known as beltline weatherstrip). These strips wipe the side windows when the glass is lowered. They come ready to install with finished ends and body curvature bends for a factory like appeara
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Leaf Spring Shackle Bushing Kit - For rear of rear leaf spring. Complete with shackle bars and bolt assembly with rubber bushings. Two (2) kits required per car.
Front Coil Spring Saddle Insulator Kit - Two front coil spring bushings and two spring insulators to restore the performance of your classic vehicle. Requires two (2) per car.
Insulator, cantilever spring type rear support.
Side window vertical leading edge weatherstrip.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Kit, cowl lacing. Clips installed.
Bumpers, upper door glass. Installs on backside top of vent window frame where window rolls up.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Pads, taillight housing to body. Machine die cut to exact original dimensions. Constructed of high quality, long lasting sponge rubber. Replaces factory #C4GY-13420-A.
Insulator, gear shift.
Rear Leaf Spring Insulator Pad - An exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle. Fits 2-1/2" leaf spring.
Bumpers, hood side bumper on fender. Push in type. Four (4) piece set.
Bushing, rear spring front rubber. Two (2) required per spring.
This eleven (11) piece Front Stabilizer Bar End Link Kit is designed from original parts so it fits correctly. Two (2) kits / sets required per car as one (1) kit / set services one side of front stabilizer bar.
Pad, brake and clutch pedal. Slip over type.
Gaskets, parking light lens.
This Upper Control Arm Bumper is made with top quality rubber. Includes nut and is for six (6) cylinder models.
Grommet, antenna lead-in. For front mount type.
Bumpers, glovebox and/or fuel filler door. Used as glove box door bumpers for all models listed, used as fuel door bumper for 1950-51 cars and 57-59 retractables only.
Bumper, brake and clutch pedal arm.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Plug, brake adjustment hole. Fits five sixteenths (5/16) inch by one (1) inch slot. Most models with drum brakes.Length: 1.25 inches. Height: .875 inches.
Tip, sun visor arm boot. Used where sun visor hooks to clip in center. Two (2) required per car.