Please click on the part name in red in order to get a complete description.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Original equipment style side window horizontal seal kit (also known as beltline weatherstrip). Eight (8) piece kit includes inner and outer felt beltline weatherstrip for each door and quarter windows. These strips wipe the side windows when the glass is
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Boot, 3-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
Boot, 4-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
Hardtop roof rail weatherstrip for coupe models. Includes fasteners. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
Mount, upper motor. HiPo "289". Doughnut type.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Contains four (4) pins.
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Plug kit, complete rubber. Includes quarter drain valves and installation instructions. MCA approved. Thirty two (32) pieces.
Shackle kit, rear spring. Replaces OEM number #C6DZ-5630.
Hose, air conditioner drain. Attaches to hole in floor.
Side window vertical leading edge weatherstrip.
Insulator, steering column lower flange.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Seal kit, front fender splash shields. Includes attaching staples. Six (6) piece kit.
Seals, top of vent window to door glass. Includes rivets.
This Quarter Window To Body Post seals pair are designed from the original parts for superior fitment and sealing. These seals are located on the quarter post to window.
Seal, power brake booster push rod to firewall.
Gasket, "Shelby" rotunda bullet mirror.
Grommet, steering column to floor interior side.
Bumper, center rear axle. Mounts on floor pan.
This Door To Window seals pair are designed from the original parts for superior fitment and sealing. These seals are located on the rear edge of the front door to window. Seals may also be known as a door jamb seals.
Seal, radiator support to hood. Includes original type attaching staples.
Gasket, air cleaner lid. Cut to fit.
Gasket, air cleaner lid. Cut to fit.
Hose, fuel tank to filler pipe.
Bumper, outer rear axle. Mounts on frame rail. Push in type. Two (2) required per car.
Seal, lower ball joint dust.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
This eleven (11) piece Front Stabilizer Bar End Link Kit is designed from original parts so it fits correctly. Two (2) kits / sets required per car as one (1) kit / set services one side of front stabilizer bar.
Seal, firewall to hood. Includes attaching clips pre-installed.
Valves, quarter panel drain.
Bumpers, radiator support hood. Includes jamb nuts. Slip on "Rounded Top" type.
Upper Control Arm Bumper made with top quality rubber. Includes nut.
Hood Bumper, radiator support hood. Includes jamb nut. Vulcanized "Rounded Top" type. Two (2) required per car.
Plugs, seat access hole plugs. (Included in complete rubber plug kits). Eight (8) piece set.
Pads, parking light to body.
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole with two notches. Fits either aluminum or steel valve covers.
Bumper, door window lower stop. Installs inside door.Qty Required:2 Two (2) required per car.
Seals, back up light to body. Black.
Grommet, air conditioner hoses through firewall. Used with reproduction hoses. Has bigger holes than original.
Cover, headlight dimmer switch rubber.
Gaskets, pony interior door light.
Bumpers, trunk lid.
Grommet, air conditioner hoses through firewall. Used with original hoses.
Grommet, antenna lead-in. For front mount type.
Bumper, radiator support hood. Includes jamb nut. Slip on "Exposed Screw" type. Two (2) required per car.
Grommet, valve cover (Positive crankcase ventilation valve). Used in D-shaped hole on steel valve covers.
Seals, quarter panel extension.
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.
Seal, firewall to steering column.
Pads, trunk tension rods anti rattler.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Bumper, brake and clutch pedal arm.
Grommet, accelerator pedal rod firewall.
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole on steel valve covers.
Pads, rear bumper to body. Four (4) piece set.
Gaskets, taillight lens.
Pads, tail light mounting. White.
Grommets, fuel line to side apron.
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Gasket, fuel neck to body.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Tips, sun visor rubber.
Seals, wiper pivot to cowl. Replaces factory #C5ZZ-17475.
Gasket, left-hand air vent outlet.
Gaskets, back-up light lens.
Pads, front bumper bracket to fender. Two (2) required per car.
Bumpers, glovebox and/or license plate. Used as glove box door bumpers for 65-66 and 71-73 models, used as license plate bumper for 65-70 models.
Gaskets, parking light lens.
Bumpers, ash tray.
Bumpers, door. Push in type.Qty Required:4 Four (4) required per car.
Bumper, hood on fender.1965-66: Mustang (4 required). 1967-68: Mustang (2 required).
Pad, front fender to body pillar. Two (2) required per car.
Gasket, rear license light lens.