Convertible roof rail weatherstrip. This part fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
These front door vent window seals are designed from the original parts for superior fitment and seal. The pieces are fully molded as left and right using top quality materials.
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Original equipment style side window horizontal seal (also known as beltline weatherstrip). These strips wipe the side windows when the glass is lowered.
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Leaf Spring Shackle Bushing Kit - For rear of rear leaf spring. Complete with shackle bars and bolt assembly with rubber bushings. Two (2) kits required per car.
Channel, division bar run. Includes molded ends.
Gaskets, taillight to body.
Front Coil Spring Saddle Insulator Kit - Two front coil spring bushings and two spring insulators to restore the performance of your classic vehicle. Requires two (2) per car.
Seals, front of door seal at beltline in front of vent window.
Side window vertical leading edge weatherstrip.
Front motor mount support. Right-hand side only. Fairlane big block engines. See description for fitment.
Front motor mount support. Left-hand side only. Fairlane big block engines. See description for fitment.
This U Jamb Lock Pillar Filler pair seals the bottom of the rear side window and may also be known as a door jamb seal.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Seals, front fender to radiator support. Staples included.
Kit, cowl lacing. Clips installed.
This six (6) piece Front Fender Dust Shield / Splash Apron set is designed from the original part(s) for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
Seals, rear of front fender to cowl side panel lower extension. Staples included.
Seals, rear of front fender to cowl upper.
Valves, rear floor pan extension drain.
Rear Leaf Spring Bushing - Original style leaf spring bushings used in front eyes of rear leaf springs. Requires two (2) spring bushings per vehicle.
Pedal, accelerator. Includes chrome trim. Trucks (F100-350) before Serial # P60,001.
Pads, convertible top of quarter window on roof.
Drains, convertible top rail rear water.
Seals, headlight to fender. Gray rubber.
Pad, horn ring pressure.
Insulator, steering column lower flange.
Pad, brake pedal. Models with manual transmission and manual brakes.
Gaskets, parking light lens.
Pad, brake pedal. Models with automatic transmission and manual brakes.
Seal, top of radiator to hood. Holes pre-punched and special fasteners included.
Pad, radiator mounting. Lower.
Insulator, gear shift.
Rear Leaf Spring Insulator Pad - An exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle. Fits 2-1/2" leaf spring.
Bumpers, dual useage. Used on the rear of the hood for 1966-67: Fairlane & Ranchero. Used as a liftgate bumper for 1966-77: U-Series Bronco. Use on the door for 1967-72: F100-750 Series trucks.
Gaskets, air vent inlet duct to cowl.
Repair kit, stabilizer bar end. Eleven (11) piece set. Two (2) kits required per car. Hex head bolt. 3/8"-16nc x 6-7/8" lg. Comes with metal sleeve, four (4) cup washers and four (4) rubber grommets.
Gaskets, taillight lens.
Seal, accelerator pedal rod.
Insulator, front coil spring upper.
Bumper, front suspension. Bumper section is 1-5/8" tall, 2" long, and 1-3/8 wide.
This Clutch Pedal Rod Boot is designed from the original part for superior fitment and seal. Accordion style boot seals the clutch rod to the floor.
Gasket set, back-up light lens.
This is the Vent Window Frame Seal for the outer edge of vent window frame to front door. This special thin strip glues (adhesive is not included) on vent window frame and stops water from leaking between the vent window frame and the front door.
This Quarter Panel Drain Plug pair is a quality reproduction of the original factory part. These rubber plugs fit inside the quarter panel area to seal-out weather and environmental elements.
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Plugs, quarter panel drain.
Bumpers, fender to hood. Used in top of fender. Four (4) piece set.