This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This eight (8) piece set includes inner and outer window felt beltline weatherstrips for each side window and quarter window. For use with exterior molding.
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. Premium seals designed and molded from original parts for superior fitment and seal.
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Boot, 3-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
This Door Weatherstrip is designed from the original parts. These gaskets are the the primary door to body weatherstrips. Molded ends with metal cores. Includes two (2) pins.
Boot, 4-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
This Hardtop Roof Rail Weatherstrip pair is for coupe models. Includes fasteners. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
This thirty-three (33) piece Body Plug and Grommet set is designed from the original parts for superior fitment and sealing. Mustang Club of America (MCA) approved.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Seals, tail light housing to body. Ten (10) piece set.
Door lock pillar seal (Built before 12/14/66). This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core. Comes with screws for easy installation.
This Peel-N-Stick Trunk Lid Weatherstrip is designed for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk lid to seal directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
These Front of Vent Window to Door Seals are installed at the front of the door and next to the door weatherstrip. Sold as a pair.
This Accelerator Pedal Pad is made of top-quality EPDM rubber with a high level of fit and finish. Designed to be a direct fit reproduction.
Side window vertical leading edge weatherstrip.
This Trunk Lid Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Constructed of a durable rubber and is a direct-fit replacement. This product is sold as a pair.
Rear Leaf Spring Insulator Pad - An exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle. Fits 2-1/2" leaf spring.
Gasket, mirror. Left-hand only.
Bumper, center rear axle. Mounts on floor pan.
Door lock pillar seal (Built on or after 12/14/1966). Back of door to window. This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core.
Seal, radiator support to hood. Includes original type attaching staples.
Hose, fuel tank to filler pipe.
Gaskets, taillight lens.
Gasket, trunk lock.
Bumper, front suspension. Includes nut.
Bumpers, headlight door. Two (2) pair required per car.
This Clutch Pedal Rod Boot is designed from the original part for superior fitment and seal. Accordion style boot seals the clutch rod to the floor.
This eleven (11) piece Front Stabilizer Bar End Link Kit is designed from original parts so it fits correctly. Two (2) kits / sets required per car as one (1) kit / set services one side of front stabilizer bar.
This Firewall to Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
This bumper is made from high-quality EPDM dense rubber for the Builder’s creative application and use.
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
This is the Vent Window Frame Seal for the outer edge of vent window frame to front door. This special thin strip glues (adhesive is not included) on vent window frame and stops water from leaking between the vent window frame and the front door.
Plugs, seat access hole plugs. (Included in complete rubber plug kits). Eight (8) piece set.
Bumper, door window lower stop. Installs inside door.Qty Required:2 Two (2) required per car.
Seals, back up light to body. Gray.
Cover, headlight dimmer switch rubber.
Bumpers, trunk lid.
Grommet, antenna lead-in. For front mount type.
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.
Seal, firewall to steering column.
Grommet, integral air conditioner condenser tubes to radiator support. Made from flat foam rubber.
Pads, rear bumper to body. Four (4) piece set.
Grommets, fuel line to side apron.
Grommets, fuel line to side apron.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Gasket, fuel neck to body.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Tips, sun visor rubber.