Please click on the part name in red in order to get a complete description.
Hardtop roof rail weatherstrip. Includes fasteners. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. Premium seals designed and molded from original parts for superior fitment and seal.
Original equipment style side window horizontal seal kit (also known as beltline weatherstrip). Four (4) piece kit includes inner and outer felt beltline weatherstrip for both door windows. These strips wipe the side windows when the glass is
Boot, 3-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
Boot, clutch release lever. Made from Original Ford tooling.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Molded ends with metal cores. Includes two (2) pins.
Boot, 4-speed manual transmission lower shifter. Exact reproduction of original. Surrounds shifter housing sealing out dirt, moisture and noise.
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Plug kit, complete rubber. Includes quarter drain valves and installation instructions. MCA approved. Thirty eight (38) piece set.
Mount, upper motor. HiPo "289". Doughnut type.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Shackle kit, rear spring. Replaces OEM number #C6DZ-5630.
Seals, taillight housing to body. Thick mount type.
Hose, air conditioner drain. Attaches to hole in floor.
Seals, front of vent window to door seals.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Seal kit, front fender splash shields. Includes original type plastic fasteners. Ten (10) piece kit.
Insulators, lower radiator mounting.
Insulators, upper radiator mounting.
Pads, tail light bezel. Six (6) piece set.
Bumpers, fastback fold down rear seat to floor stop. Includes jamb nuts.
Valves, quarter panel drain.
Bumper, center rear axle. Mounts on floor pan.
Door lock pillar seal (Built on or after 12/14/1966). Back of door to window. This part seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core.
Seal, radiator support to hood. Includes original type attaching staples.
Gasket, air cleaner lid. Cut to fit.
Hose, fuel tank to filler pipe.
Gaskets, "Shelby" tail light lens.
Bumper, outer rear axle. Mounts on frame rail. Push in type. Two (2) required per car.
Bumper, front suspension. Includes nut.
Gasket, air cleaner lid. Cut to fit.
Seal, clutch pedal rod to firewall.
Seal, lower ball joint dust.
Seal, firewall to hood. Includes attaching clips.
Bumpers, fastback fold down rear seat latch.
Bumpers, radiator support hood. Includes jamb nuts. Slip on "Rounded Top" type.
Hood Bumper, radiator support hood. Includes jamb nut. Vulcanized "Rounded Top" type. Two (2) required per car.
Bumpers, fastback fold down seat frame side. Four (4) piece set.
This is the Vent Window Frame Seal for the outer edge of vent window frame to front door. This special thin strip glues (adhesive is not included) on vent window frame and stops water from leaking between the vent window frame and the front door.
Plugs, seat access hole plugs. (Included in complete rubber plug kits). Eight (8) piece set.
Gaskets, taillight lens.
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole with two notches. Fits either aluminum or steel valve covers.
Bumper, door window lower stop. Installs inside door.Qty Required:2 Two (2) required per car.
Seals, back up light to body. Gray.
Seals, front fender front extension.
Cover, headlight dimmer switch rubber.
Bumpers, trunk lid.
Grommet, valve cover (Positive crankcase ventilation valve). Used in D-shaped hole on steel valve covers.
Gaskets, deluxe interior door light.
Shield, rear license plate light.
Seals, quarter panel extension.
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.
Seal, firewall to steering column.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Grommet, integral air conditioner condenser tubes to radiator support. Made from flat foam rubber.
Grommet, accelerator pedal rod firewall.
Grommet, oil cap elbow.
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole on steel valve covers.
Pads, rear bumper to body. Four (4) piece set.
Grommets, fuel line to side apron.
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Gaskets, hood mounted turn indicator light lens.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Gasket, fuel neck to body.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Tips, sun visor rubber.
Seals, wiper pivot to cowl. Replaces factory #C5ZZ-17475.
Gasket, trunk lock cylinder.
Gasket, left-hand air vent outlet.
Gaskets, back-up light lens.
Pads, front bumper bracket to fender. Two (2) required per car.
Bumpers, glovebox and/or license plate. Used as glove box door bumpers for 65-66 and 71-73 models, used as license plate bumper for 65-70 models.
Bumpers, glovebox door.
Bumper, rear hood. Two (2) required per car.
Gaskets, parking light lens.
Gaskets, front marker light lens.
Bumpers, door. Push in type.Qty Required:4 Four (4) required per car.
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Bumper, hood on fender.1965-66: Mustang (4 required). 1967-68: Mustang (2 required).
Gasket, rear license light lens.