Original equipment style side window horizontal seal kit (also known as beltline weatherstrip). This 8 piece kit includes inner and outer felt beltline weatherstrip for each door and quarter windows.
Hardtop roof rail weatherstrip. Includes fasteners. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Molded ends with metal cores.
Made from Original style material. Side window outer horizontal seal (also known as beltline weatherstrip). These strips wipe the side windows when the glass is lowered.
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Seal, fuel filler pipe to trunk floor.
Mount, upper motor. HiPo "289". Doughnut type.
Shackle kit, rear spring. Replaces OEM number #C6DZ-5630.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Plug kit, complete rubber. Does NOT include quarter drain valves. Includes installation instructions. MCA approved. Thirteen (13) piece set.
Seal, firewall to hood. Includes attaching clips.
Bumper, front suspension. Includes nut.
Valves, quarter panel drain.
Gaskets, rear spoiler.
Gasket, air cleaner lid. Cut to fit.
Bumpers, outer rear axle. Mounts on frame rail. Push in type. Two (2) required per car.
Gasket, air cleaner lid. Cut to fit.
This Clutch Pedal Rod Boot is designed from the original part for superior fitment and seal. Accordion style boot seals the clutch rod to the floor.
Seal, lower ball joint dust.
Pad, parking brake pedal.
Seal, tie rod end dust.
This bumper is made from high-quality EPDM dense rubber for the Builder’s creative application and use.
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Bumpers, firewall to hood. Includes attaching screws. Three (3) piece set.
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole with two notches. Fits either aluminum or steel valve covers.
Cover, headlight dimmer switch rubber.
Seal, firewall to steering column.
Grommet, valve cover (Positive crankcase ventilation valve). Used in D-shaped hole on steel valve covers.
Seals, quarter panel extension.
Seal, wiper motor to firewall. Replaces factory #D1ZZ-17430.
Seal, automatic transmission shifter housing to floor. Installs between housing and floor pan.
Grommet, oil cap elbow.
Gaskets, parking light lens.
Grommet, valve cover (Positive crankcase ventilation valve). Used in round hole on steel valve covers.
Pads, rear bumper to body. Four (4) piece set.
Seals, front marker light to body.
Seals, rear marker light to body.
Grommets, fuel line to side apron. Three (3) required per car.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Gasket, fuel neck to body.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Tips, sun visor rubber.
Gasket, trunk lock cylinder.
Bumpers, glovebox and/or license plate. Used as glove box door bumpers for 65-66 and 71-73 models, used as license plate bumper for 65-70 models.
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Gasket, rear license light lens.