1/2" Standard Bumper
p/n: 33-0496-71
This Standard Bumper is fully molded and designed from the original part for correct fitment and seal. Designed for applications such as door opening at upper corner, license plate, and fuel filler door. Self-retaining type bumper.
1-3/4" Rear Door Bumper
p/n: 35-1030-71
Bumper, rear door. Plug style. Compare with your original, use as required.
3/4" Door Bumper
p/n: 33-0293-71
Bumper, front door pillar, upper and lower. Replaces factory #3720168.
3/4" Hood and Door Bumper
p/n: 33-0459-42
This Hood and Door Bumper is fully molded and designed from the original part for superior fitment and seal. Designed for hood to cowl and door hinge pillar upper bumper. May be used in both places.
Brake shaft stop bumper
p/n: 70-0271-24
Bumper, brake rocker shaft lever stop. Two (2) used per car. Also used as door side bumper for some 1927-31 Cadillacs.
Bumpers - Filler Door/Lower Door/Rear License Plate Support
p/n: 20-1302-41
A rubber Bumper pair designed from the original part for superior fitment, finish and function. Fits to the lower door and / or the fuel filler cover and / or the license plate support. Type with threaded end.
Door Alignment Pad
p/n: 60-0060-71
Wedge pad, door aligning dovetail. Goes under bumper retainer.Length: .9375 inches. Width: .9375 inches. Height: .4375 inches.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Door Bumper
p/n: 40-0154-70
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface.Length: 1.0 inches.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 70-1563-71
Bumper, door edge.Length: 1.0 inches. Width: .625 inches. Height: .75 inches.
Door Bumper
p/n: 60-0032-71
Pad, door jamb. One (1) per door.Length: 1.25 inches. Width: .75 inches. Height: .875 inches.
Door Bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Door Bumper
p/n: 17-0041-70
Pad, door jamb, large size, retained by both dovetail retainer from back, and screw through center. Usually 2 per door.Length: 2.125 inches. Width: 1.
Door Bumper
p/n: 33-0981-71
This Door Bumper is designed from the original part for superior fitment, finish and function. Molded with push in carrot retainers, this bumper is commonly used as a upper door bumper on GM models.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 70-2608-71
This Door Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires four (4) bumpers each per vehicle.