1/2" Standard Bumper
p/n: 33-0496-71
This Standard Bumper is fully molded and designed from the original part for correct fitment and seal. Designed for applications such as door opening at upper corner, license plate, and fuel filler door. Self-retaining type bumper.
1/4" Fuel Tank Mounting Isolator Strapping
p/n: 70-3612-99
Universal 1/4" Fuel Tank Mounting Isolator Strapping. Made of high quality 60 durometer EPDM dense rubber for a variety of uses. Available by the foot.
1-5/16" Fuel Line Grommet
p/n: 32-0714-41
This Fuel Line Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed to run the fuel line through the firewall.
5/16" Glovebox Door Bumper
p/n: 33-0128-88
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.
5/16" Standard Stem Bumper - GM
p/n: 33-0127-41
This 5/16" Standard Stem Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a console and fuel filler door bumper on GM models.
9/16" Taillight Bumper
p/n: 33-0556-15
Taillight body upper half and fuel filler cover to lower half bumper.
Accelerator Hinge Grommet
p/n: 30-0539-41
Grommet, accelerator pedal hinge to floorboard. Length: 3.50 inches. Width: 2.50 inches.
Accelerator Lever to Accelerator Shaft Seal
p/n: 70-4098-40
This Accelerator Lever to Accelerator Shaft Seal is designed from the original part for superior fitment and seal. This seal mounts directly to cover and protect the accelerator lever to accelerator shaft rod linkage connection.
Accelerator Pedal Rod Firewall Grommet
p/n: 20-2744-41
This Accelerator Pedal Rod Firewall Grommet is used to run the accelerator pedal rod through the firewall. Designed from original part so it fits correctly.
Accelerator Pedal Rod Grommet
p/n: 20-0044-41
This Accelerator Pedal Rod Grommet is used to wrap around the accelerator rod at the firewall. Designed from the original part for superior fit and seal.
Accelerator Pedal Rod Seal
p/n: 20-1450-41
This Accelerator Pedal Rod Seal is used to run the pedal linkage to the firewall. Designed from the original part for superior fit and seal.
Accelerator Pedal Rod Seal
p/n: 20-2745-41
This Accelerator Pedal Rod Seal is used when running the accelerator rod through the firewall. The seal helps to block out air and wind noise from entering into the cabin.
Accelerator Pedal Rod Seal
p/n: 20-0128-41
This Accelerator Pedal Rod Seal is used to wrap around the accelerator rod linkage at the firewall. Designed from original part so it fits correctly.
Accelerator Pedal Rod Seal
p/n: 20-1449-41
This Accelerator Pedal Rod Seal is used to run the pedal linkage to the firewall. Made from top quality rubber to ensure durability and proper fitment.
Accelerator Pedal Rod Seal
p/n: 20-1448-41
This Accelerator Pedal Rod Seal is used to run the pedal linkage to the firewall. Designed from original part so it fits correctly.
Accelerator Rod Seal
p/n: 40-0205-88
This Accelerator Rod Seal is used as an accelerator rod through the toeboard. Molded from a high-quality EPDM dense rubber.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Air Inlet Hose
p/n: 70-0405-41
Hose, air inlet, radiator shroud to air silencer. Two and one eighths (2-1/8) inch outside diameter by nine and three eighths (9-3/8) inch long. Beautiful copy of rare original part.
Bumpers - Filler Door/Lower Door/Rear License Plate Support
p/n: 20-1302-41
A rubber Bumper pair designed from the original part for superior fitment, finish and function. Fits to the lower door and / or the fuel filler cover and / or the license plate support. Type with threaded end.
Carburetor Air Intake Hose
p/n: 70-0290-41
Hoses, carburetor air intake. Two (2) per car. Sixteen and three fourths (16-3/4) inches long, two (2) inches inside diameter one end, two and one fourth (2-1/4) inches inside diameter other end. Trim to proper length when installing.
Choke Cable Support At Ignition Cable Grommet
p/n: 60-0373-13
This Choke Cable Support At Ignition Cable Grommet is designed from the original part for superior fitment and function.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Filler Neck Extension Pad
p/n: 70-0123-41
Mounting pad, filler neck extension. Four and nine sixteenths (4-9/16) inches diameter, double bead.
Fuel Door Bumper
p/n: 33-3450-41
Bumper, fuel door. Pushes into body inside fuel filler recess. 5/16" head length by 5/32" head height. Two (2) required per car.
Fuel filler cover bumper
p/n: 20-0006-41
Bumpers, fuel tank door. Single stem and double retainer bumper set.
Fuel Filler Cover Bumper
p/n: 33-0557-15
Bumper, taillight body upper half and fuel filler cover to lower half. Four (4) per set. Length: 13/16 inches. Width: 1/2 inches.
Fuel Filler Door Bumper
p/n: 33-0538-41
This Fuel Filler Door Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the Fuel Filler Door to support / cushion the closure and prevent metal to metal contact. Usually requires two (2) bumpers each per vehicle.
Fuel Filler Dust Shield
p/n: 70-2783-45
This Fuel Filler Dust Shield is designed from the original part for superior fitment and function. Shield piece is die cut from quality masticated rubber to authentic original dimensions. Shield fits around the fuel filler neck to body.
Fuel Filler Neck Grommet
p/n: 30-0158-41
This Fuel Filler Neck To Body Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Fuel Filler Neck Inner Panel Grommet
p/n: 70-1908-41
This Fuel Filler Neck Inner Panel Grommet is designed from the original part for superior fitment and seal. This flat grommet fits around the vehicles fuel filler neck at the inner panel.