Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Quarter Window Lock Pillar Fillers
p/n: 60-0602-79
This Quarter Window Lock Pillar Filler pair seals the bottom of the rear side window, and may also be known as a u-jamb or door jamb seal. Fully molded authentic rubber construction with brass metal core.
Quarter Window U Jamb Lock Pillar Fillers
p/n: 70-1532-79
This Quarter Window U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Quarter window weatherstrip
p/n: 50-0282-77
Weatherstrip, fixed rear quarter window. Each vulcanized in one piece for ease of installation.
Quarter Window Weatherstrips
p/n: 27-0040-77
This Quarter Window Weatherstrips pair is designed from the original part for superior fitment and seal. This seal mounts around the full perimeter of the quarter glass for a precise, factory fit. For fixed, stationary windows only.
Radiator bracket cushion
p/n: 50-0324-42
Bumper for bracket, radiator upper panel to grill. Use original steel bracket.Buick 1941: 1 required per car. 1942: Part not used for this year.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Rear Axle Suspension Bumper
p/n: 70-2638-35
This Rear Axle Suspension Bumper is fully molded with new rubber vulcanized to new steel cores. Used on all models with conventional spring suspension.
Rear Bumper Grommet
p/n: 50-0126-29
Grommets, rear bumper. Hollow construction for good fit. Fully molded rubber with locating tabs.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Rear Door Lock Pillar Weatherstrips
p/n: 70-1907-79
This Rear Door Lock Pillar Weatherstrip pair seals the bottom of the rear side window, and may also be known as a door jamb seal. Fully molded authentic rubber construction with metal core. For rear doors.
Rear Door Vent Weatherstrips
p/n: 70-3621-74
These Rear Door Vent Weatherstrips are designed from the original parts for superior fitment and seal. They are molded as left and right and with the correct curve for a flawless fit around the bend.
Rear Door Weatherstrip
p/n: 82-0141-72
This Rear Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Made of quality sponge rubber with molded corners to ensure a durable positive seal.
Rear Door weatherstrip
p/n: 70-1825-72
Rear door edge weatherstrip. This set is the primary door to body weatherstrip and consists of lock side and hinge side door sealing strips with integral molded ends for both rear doors. Just like the original part these strips are designed to be butt-joi
Rear Door weatherstrip
p/n: 90-0132-72
Rear door edge weatherstrip. This part is the primary door to body weatherstrip. Includes the perimeter seal for both rear doors and the molded corners. Set consists of four (4) pieces. Kit does not include adhesive. Includes the following components
Rear Door Weatherstrip
p/n: 50-0534-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Rear Door Weatherstrip Set
p/n: 90-0107-72
This Rear Door Weatherstrip Set is the primary door to body weatherstrip. This includes the weatherstrips for the sides and bottom of the door.
Rear Door Weatherstrip Set
p/n: 90-1823-72
This Rear Door Weatherstrip Set is the primary door to body weatherstrip. Clips included for easy installation.
Rear Door Weatherstrip Set
p/n: 90-0105-72
This Rear Door Weatherstrip Set is the primary door to body weatherstrip.
Rear Door Weatherstrip Set
p/n: 90-0103-72
This Rear Door Weatherstrip Set is the primary door to body weatherstrip.
Rear Door Weatherstrip Set
p/n: 90-0101-72
This Rear Door Weatherstrip Set is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (glue-on) directly to the left and right rear doors sealing the full perimeter of the doors against the vehicle body when the door is closed.
Rear Door Weatherstrips
p/n: 70-1834-72
This Rear Door Weatherstrip pair is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (pin-on) directly to the left and right rear doors sealing the full perimeter of the doors against the vehicle body when the door is closed.
Rear Door Weatherstrips
p/n: 70-1857-72
This Rear Door Weatherstrip pair is the primary door to body weatherstrip. A door edge weatherstrip with molded ends. Includes clips and fasteners for easy installation.
Rear Door Weatherstrips
p/n: 82-0191-72
This Rear Door Weatherstrip pair is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (glue-on) directly to the left and right doors sealing the full perimeter of the doors against the vehicle body when the door is closed.
Rear Door Weatherstrips
p/n: 70-1780-72
This Rear Door Weatherstrip pair is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (pin-on) directly to the left and right rear doors sealing the doors against the vehicle body when the door is closed.
Rear Quarter Vent Window Weatherstrips
p/n: 38-0058-76
This Rear Quarter Vent Window Weatherstrip pair is a four (4) piece pair. Fits both driver (Left) and passenger (Right) rear doors of the vent / wing window assemblies.
Rear Quarter Vent Window Weatherstrips
p/n: 38-0021-76
This four (4) piece Rear Quarter Vent Window Weatherstrip set contains the main vent window seals and division post seal for the rear quarter window. All of the pieces were designed from original parts for a precise and like factory correct fit.
Rear Quarter Window Gaskets
p/n: 70-2328-77
This Rear Quarter Window Gasket pair contains the left and right side weatherstrips for the two (2) large side windows on the rear quarter of the vehicle. Fully molded with factory type extrusion and corners.
Rear Roof Rail Weatherstrips
p/n: 70-3423-68
This Rear Roof Rail Weatherstrip pair is made of ozone resistant EPDM sponge rubber with molded ends and corners for a factory like fit. These high-quality weatherstrips fit on the roof of the vehicle and work to seal the side windows when the window is fully raised.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Rear Stabilizer Bushing
p/n: 50-0171-34
Bushings, rear stabilizer bar mounting. Fully molded rubber. One and one half inch (1 1/2") length by one and one fourth inch (1 1/4" outside diameter by nine sixteenths inch (9/16") inside hole diameter.
Rear window division bar seal
p/n: 70-0068-82
Seal, rear window divider, inner and outer for two (2) and three (3) light rear windows, two (2) piece set for one (1) division bar.
Rear Window Gasket
p/n: 60-0433-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 70-1259-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Fitted gasket provides a formed, seamless seal.
Rear Window Gasket
p/n: 70-0687-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 50-0215-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Rear Window Gasket
p/n: 50-0474-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Rear Window Gasket
p/n: 50-0241-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0469-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0278-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 50-0281-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Fitted gasket provides a formed, seamless seal.
Rear Window Gasket Set
p/n: 50-0206-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 50-0287-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Reflector gasket
p/n: 50-0360-15
Seal, reflector signal, between taillights. With correct slits for tabs on reflector. One (1) pair required per car.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Roof Rail Filler
p/n: 25-0069-73
Weatherstrip, front door upper corner, outer (at front end of flipper). Molded as left and right with a corrosion resistant brass metal core.
Roof Rail Filler
p/n: 70-1763-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes.
Rumble Seat Lid Corner Pad
p/n: 70-0048-87
Pads, rumble seat lid corners original style, rounded triangular shape.Width: 1.25 inches.
Rumble Seat Step Mounting Pad
p/n: 50-0182-44
Mounting pad, rumble seat step to fender, proper beaded edge, exact copy.Width: 4.8125 inches.
Rumble Seat Step Mounting Pad
p/n: 70-0043-44
Pad, rumble seat step mounting for fender, double beaded edge per original. Width: 4.375 inches.
Rumble Seat Weatherstrip
p/n: 70-0282-85
This Rumble Seat Weatherstrip is designed from the original part for superior fitment and seal. The pieces are molded as left and right for the lower corners.
Rumble Seat Weatherstrip
p/n: 70-0166-85
This Rumble Seat Weatherstrip is designed from the original part for superior fitment and seal. The strip seals the lower edge of the rumbleseat.
Rumble Seat Weatherstrip
p/n: 25-0025-85
This Rumble Seat Weatherstrip set is designed from original parts for superior fitment and seal. The set contains the pieces for the lower edge and corners.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Shock Absorber Bushing
p/n: 70-0547-32
This Shock Absorber Bushing is manufactured with high-quality EPDM rubber to OEM specifications. The bushing is the double cone style. Designed from original part to ensure proper fit.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Side Mount Cover Pad
p/n: 70-0077-37
Pads, channel type, for sidemount covers. Eight (8) piece set.Width: .25 inches. Height: .6875 inches.
Side Window Bumper
p/n: 60-0195-62
Anti-rattle, side window, inner and outer. Fits slot in outer door body metal and inner window frame (garnish molding).
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Sliding Quarter Window Seal
p/n: 60-0398-78
Weatherstrip, sliding quarter window. Mounted vertically in body where leading edge of sliding window fits when closed. Right & left rubber only.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Stabilizer Bushing
p/n: 50-0520-34
Bushing, stabilizer bracket. Constructed of durable BUNA rubber. One and five eighths inch (1 5/8") length by one and one half inch (1 1/2") outside diameter by three fourths inch (3/4") inside hole diameter.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Steering Column Floorplate
p/n: 50-0415-36
Floorplate, steering column. Black rubber. For brown see our #50-0415-89.Length: 4.125 inches. Width: 4.125 inches.
Steering Column Floorplate
p/n: 70-2578-36
Floor plate, steering column at floorboard. Durable black rubber construction with metal core just like original.
Steering Column Floorplate
p/n: 50-0565-36
Floorplate, steering column at floorboard. Black rubber. For brown (tan) see our #50-0565-89. Made with brass core.Length: 9.375 inches. Width: 5.25 inches.
Steering Column Floorplate
p/n: 50-0412-36
Floorplate, steering column. Metal core just like the original.
Steering Column Floorplate
p/n: 50-0260-36
Retainer, front floor mat on steering column (also called steering column floorplate). Black rubber. For brown see our #50-0260-89.Width: 4.3125 inches.
Steering Column Gasket - Automatic Transmission
p/n: 70-4467-36
This Steering Column gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Steering Knuckle Support Seal
p/n: 50-0525-36
Seal, steering knuckle support, upper or lower. Die cut one fourth (1/4) inch, four (4) used per car.Height: .25 inches.
Strut Rod Bushing
p/n: 50-0522-27
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Support Arm Bumper
p/n: 50-0526-32
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Tailgate bumper
p/n: 70-2854-87
Bumper, tailgate support. Two (2) bumpers mount on tailgate and two (2) mount on body in lower sections. Four (4) required.
Tailgate Weatherstrip
p/n: 70-3424-84
This Tailgate Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts to the sides and bottom of the tailgate with properly spaced plastic clips. Includes molded ends.