Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Side Mount Cover Pad
p/n: 70-0077-37
Pads, channel type, for sidemount covers. Eight (8) piece set.Width: .25 inches. Height: .6875 inches.
Side Window Bumper
p/n: 60-0195-62
Anti-rattle, side window, inner and outer. Fits slot in outer door body metal and inner window frame (garnish molding).
Side window leading edge
p/n: 60-0642-80
Side window vertical leading edge weatherstrip. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Molded authentic rubber construction with metal core, this part does not include the chrome piece
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Sliding Quarter Window Seal
p/n: 60-0398-78
Weatherstrip, sliding quarter window. Mounted vertically in body where leading edge of sliding window fits when closed. Right & left rubber only.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-2798-45
This Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pair pieces are die cut from quality masticated rubber to authentic original dimensions. This filler pair fits over suspension a-arms and inside front inner fenders.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Stabilizer Bushing
p/n: 50-0520-34
Bushing, stabilizer bracket. Constructed of durable BUNA rubber. One and five eighths inch (1 5/8") length by one and one half inch (1 1/2") outside diameter by three fourths inch (3/4") inside hole diameter.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Steering Column Floorplate
p/n: 50-0415-36
Floorplate, steering column. Black rubber. For brown see our #50-0415-89.Length: 4.125 inches. Width: 4.125 inches.
Steering Column Floorplate
p/n: 70-2578-36
Floor plate, steering column at floorboard. Durable black rubber construction with metal core just like original.
Steering Column Floorplate
p/n: 50-0260-36
Retainer, front floor mat on steering column (also called steering column floorplate). Black rubber. For brown see our #50-0260-89.Width: 4.3125 inches.
Steering Column Floorplate
p/n: 50-0412-36
Floorplate, steering column. Metal core just like the original.
Steering Column Gasket - Automatic Transmission
p/n: 70-4467-36
This Steering Column gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Steering Knuckle Support Seal
p/n: 50-0525-36
Seal, steering knuckle support, upper or lower. Die cut one fourth (1/4) inch, four (4) used per car.Height: .25 inches.
Strut Rod Bushing
p/n: 50-0522-27
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Support Arm Bumper
p/n: 50-0526-32
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Support Arm Bumper
p/n: 50-0261-32
Bumper, steering knuckle support upper arm (for front shock absorber arm).Width: 1.5 inches.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Tailgate bumper
p/n: 70-2854-87
Bumper, tailgate support. Two (2) bumpers mount on tailgate and two (2) mount on body in lower sections. Four (4) required.
Tailgate Bumper - Upper and Lower
p/n: 70-1827-87
This upper / lower Tailgate Bumper is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over corrosion resistant brass cores to ensure durability and function.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
Tailgate Outer Window Felt Weatherstrip
p/n: 80-0011-57
This reproduction Original material Tailgate Glass Outer Window Felt Weatherstrip is designed from the original part for superior fitment and seal. This flat chrome bead outer window felt wipes the outside tailgate window glass when the glass is lowered.
Tailgate Weatherstrip
p/n: 82-0181-84
This tailgate weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the sides and bottom of the tailgate opening directly to the body. Includes molded ends.
Tailgate wedge
p/n: 70-2855-87
Wedge, tailgate bumper anti-rattler. Mounts on both end jamb areas on tailgate.
Taillight Gasket
p/n: 50-0355-15
Gasket, rear stop and turn signal. Four (4) piece set required per car.
Taillight Lens and Housing Gaskets
p/n: 70-4912-15
This Taillight Lens and Housing Gasket set is designed from the original part for superior fitment and seal. Includes gaskets for Lens to Housing (2) and Housing to Body (2).
Taillight Lens And Housing Gaskets
p/n: 70-4168-15
This four (4) piece Taillight Lens And Housing Gasket set is designed from the original part for superior fitment and seal. This set does both taillights. Includes two (2) light lens to the housing gaskets and two (2) housing to vehicle body gaskets.
Taillight Lens Gasket
p/n: 50-0411-15
Gasket, taillight lens. Die cut three sixteenths (3/16) inch sponge rubber as original.Width: 6.25 inches. Height: 3.25 inches.
Taillight Mounting Pad
p/n: 50-0100-15
Mounting pad, extrusion, taillight body-to-rear fender. Sold in sets sufficient for two (2) taillights. Length: 55.0 inches. Width: .3125 inches.