Rear Door Weatherstrips
p/n: 70-4741-72
These primary Rear Door Weatherstrips mount (pin) directly to the left and right rear doors sealing the full perimeter of the doors against the vehicle body when the door is closed. Includes 32 sockets for easy installation.
Rear Stationary Side Window Weatherstrips
p/n: 70-3606-77
This Rear Stationary Side Window Weatherstrip pair is designed from the original part for superior fitment and seal. This seal mounts around the full perimeter of the rear stationary glass for a precise, factory fit. For stationary windows only.
Front Door Vent Window Set
p/n: 90-0419-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Windshield Gasket
p/n: 50-0291-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Vent Window Weatherstrips
p/n: 38-0082-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Transmission Mount Service
p/n: 50-0463-25
Mount, transmission support. One (1) per car. Revulcanization service only.Length: 5.25 inches. Width: 2.25 inches.
Rear Window Gasket Set
p/n: 70-3605-81
This Rear Window Gasket Set mounts around the two (2) smaller windows on each side of the back glass on the liftgate. They are molded as left and right with properly shaped corners for a precise, factory fit.
Window Sash Steel Channels
p/n: 50-0552-59
This Window Sash Steel Channel pair is designed from the original part for superior fitment and function. Ready for attaching to your original brackets. Twenty (20) inches long.
Window Sash Steel Channels
p/n: 50-0553-59
This rear door Window Sash Steel Channel pair is designed from the original part for superior fitment and function. Ready for attaching to your original brackets. Twenty-five and one half (25-1/2) inches long.
Beltline Weatherstrip
p/n: 70-0961-60
This Beltline Weatherstrip is thick pile lined without chrome bead. Available in 4ft pairs.
Liftgate Weatherstrip
p/n: 70-2250-85
This Liftgate Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the liftgate opening directly to the body.
Beltline Weatherstrip
p/n: 70-2251-60
Weatherstrip, front door window outer scraper seal at beltline. Original type with bright bead attached to seal. Made with proper attaching clips.
Beltline Weatherstrip
p/n: 70-2252-60
Weatherstrip, rear door window outer scraper seal at beltline. Original type with bright bead attached to seal. Made with proper attaching clips.
Outer Beltline Weatherstrip
p/n: 50-0549-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Beltline Weatherstrips
p/n: 70-1121-61
These Beltline Weatherstrips (sometimes called "scraper seal") come in a three (3) foot pair. For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 3ft pair.
Beltline Weatherstrip
p/n: 70-1120-61
This Beltline Weatherstrip comes in a six (6) foot length for the outer beltline (sometimes called "scraper seal"). For use on front, rear, and quarter windows without a chrome reveal molding at the window beltline. Available in 6ft lengths.
Beltline Weatherstrip
p/n: 50-0550-60
Weatherstrip, beltline front door inner. Correct material with installed clips.Width: .4375 inches.
Beltline Weatherstrip
p/n: 50-0551-60
Weatherstrip, beltline rear door inner. Correct material with installed clips.Width: .4375 inches.
Outer Beltline Weatherstrip
p/n: 50-0548-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door. Designed like original with attaching tabs.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Vent Window Division Bar Weatherstrips
p/n: 50-0337-56
This Front Vent Division Bar Weatherstrip pair is fully molded with a metal core and attaching tabs. This piece mounts on the vertical division bar and seals as the vent glass closes against it.
Flexible Run Channel
p/n: 60-0583-58
Made with an electrostatic flocked rubber that has flexibility and reduces friction to secure and let the glass slide inside the channel. Available in 96" lengths.
Taillight Lens and Housing Gaskets
p/n: 70-4912-15
This Taillight Lens and Housing Gasket set is designed from the original part for superior fitment and seal. Includes gaskets for Lens to Housing (2) and Housing to Body (2).
Radiator Bracket Cushion
p/n: 70-2014-31
Radiator support bracket, insulator, upper. Two (2) used per car.Length: 6.0 inches.
Radiator Bracket Cushion
p/n: 70-2229-31
Radiator support bracket, insulator, lower. Two (2) used per car.Length: 4.5 inches.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Door Handle Gasket Set
p/n: 50-0560-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Beltline Guide Plate - Plastic
p/n: 50-0384-62
This Beltline Guide Plate is designed from the original part for superior fitment and function. High quality plastic plate attaches to various outer beltline window scraper weatherstrips.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Body Mount Isolator Pad
p/n: 50-0507-48
Isolator, body mounting. Fully molded rubber. Two inches (2") outside diameter by seven eighths inch (7/8") inside hole diameter by three fourths inch (3/4") height.
Rear License Light Assembly Gasket Set
p/n: 50-0357-17
This Rear License Light Assembly Gasket Set is designed from the original part for superior fitment and seal. One (1) die cut rubber ring and one (1) die cut cork gasket comprise the set.
Plastic Guide Plate
p/n: 50-0385-58
Plastic guide plate, attaches to various outer scraper weatherstrips.Length: 1.625 inches. Width: .625 inches.
Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Tailgate Bumper - Upper and Lower
p/n: 70-1827-87
This upper / lower Tailgate Bumper is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over corrosion resistant brass cores to ensure durability and function.
13/16" Door Weatherstrip with Clips
p/n: 70-1245-73
This Door Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Steering Knuckle Support Seal
p/n: 50-0199-35
This Steering Knuckle Support Seal is designed from the original part for an authentic fit, finish, and appearance. Fits at the steering knuckle support at the upper pivot pin. Four (4) required per car.
Hood Bumper
p/n: 70-2020-42
Bumper, hood ledge. Original type retainer and proper factory type profile.Width: .75 inches. Height: 1.25 inches.