Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Door Weatherstrip
p/n: 50-0219-73
This Door Weatherstrip is made of a high-quality sponge extrusion to original configuration. This weatherstrip is for the front door opening, lower front body hinge pillar.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Parking and Signal Gasket
p/n: 50-0354-16
Gasket, front parking and signal light to fender. One (1) pair per car. Fits between signal lamp body and headlamp to fender adapter.Width: 4.0 inches.
Heater control valve seal
p/n: 50-0347-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Parking Light Lens Gasket
p/n: 50-0351-16
Gasket, headlight door parking lens. Constructed out of soft durable rubber.Height: .375 inches.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Brake Pedal Pad
p/n: 50-0349-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. For models with Power Brakes.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Parking Light Lens Gasket
p/n: 50-0353-16
Gasket, front parking lens. High quality sponge rubber better than original. One (1) pair per car.Width: 3.375 inches. Height: 2.625 inches.
Parking Brake Pedal Pad
p/n: 50-0348-22
Pad, parking brake pedal. Without "PARK" written on pad. Black only. For pedal pad with "PARK" written on pad see our #50-0405-22.Height: 2.0 inches.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
Reflector gasket
p/n: 50-0360-15
Seal, reflector signal, between taillights. With correct slits for tabs on reflector. One (1) pair required per car.
Wiring grommet
p/n: 50-0346-21
Grommet, spark plug wire. Trapezoidal style under spark plug cover flange at right end of both sides. One (1) pair required per car with our #50-0345-21.
Wiring grommet
p/n: 50-0345-21
Grommet, spark plug wire. Oblong style for spark plug wire clip at right rear of head. One (1) pair required per car with our #50-0346-21.Width: 1.
Brake Pedal Pad - Dyna-Flow Transmission
p/n: 50-0285-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. For models with Dyna-Flow and standard brakes.
Heater control valve seal
p/n: 50-0356-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water. For all except right-hand drive.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Taillight Mounting Pad
p/n: 50-0410-15
Pad, taillight to fender. Width: 7.25 inches. Height: 4.0 inches.
Door Handle Gasket Set
p/n: 50-0322-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Taillight Lens Gasket
p/n: 50-0411-15
Gasket, taillight lens. Die cut three sixteenths (3/16) inch sponge rubber as original.Width: 6.25 inches. Height: 3.25 inches.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Hood Bumper
p/n: 50-0159-42
Bumper, hood ledge corner at shroud.Width: 1.25 inches. Height: .5 inches.
Body Mounting Pad
p/n: 50-0478-48
Pad, body mounting. Fully molded rubber with locating collar. Two (2) are needed per car.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Body Mounting Pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Parking, Signal or Backup Light Lens Gaskets
p/n: 50-0381-16
This front Parking and Turn Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel. Also fits Backup Light Lens on cars with optional Backup Lights.
Hood Bumper
p/n: 50-0277-42
Bumper, hood side to fender ledge. Metal core molded in as original.Width: 1.875 inches. Height: .8125 inches.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
1-5/8" Firewall Grommet
p/n: 50-0364-20
This Firewall Grommet is used to run the oil pressure and water temperature, or washer vacuum hose through the firewall. Designed from original part for excellent workmanship.
1-5/8" Firewall Grommet
p/n: 50-0363-20
This Firewall Grommet is used to run the windshield washer hose through the firewall. Designed from original part for excellent workmanship.
Body Mounting Pad
p/n: 50-0097-48
Pad, several usages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car.
License lens gasket
p/n: 50-0357-17
Gasket set, rear license light assembly. One (1) rubber ring and one (1) cork rubber gasket comprise set.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
Hood Bumper
p/n: 50-0490-42
Bumper, hood to fender. Uses four (4) per car for most models.Width: 1.375 inches. Height: 1.25 inches.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.