Peel-N-Stick Trunk Weatherstrip
p/n: 70-0774-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Trunk Hinge Mounting Pad
p/n: 50-0115-87
Mounting pad, trunk strap hinge, four (4) piece set.Length: 7.25 inches.
Taillight Lens Gasket
p/n: 50-0492-15
Gasket, taillight lens.Width: 14.5 inches. Height: 7.5 inches.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Trunk Hinge Mounting Pad
p/n: 50-0372-87
Pad, trunk hinge. Non-bead cushion like original. Four (4) piece set.Length: 7.125 inches.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Parking, Signal Light Lens Gaskets - Front
p/n: 50-0192-16
This front Parking and Turn Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel.
Leading Edge Weatherstrip
p/n: 70-2002-80
Rear door window vertical seals. Fully molded rubber with metal cores.
Taillight Mounting Pad
p/n: 50-0491-15
Pad, taillight mounting. Width: 16.0 inches. Height: 9.0 inches.
Brake Pedal Pad
p/n: 50-0349-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. For models with Power Brakes.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Rumble Seat Step Mounting Pad
p/n: 50-0182-44
Mounting pad, rumble seat step to fender, proper beaded edge, exact copy.Width: 4.8125 inches.
Parking Light Lens Gasket
p/n: 50-0351-16
Gasket, headlight door parking lens. Constructed out of soft durable rubber.Height: .375 inches.
Cowl Vent Weatherstrip
p/n: 50-0123-54
Weatherstrip, cowl vent lid (top), sponge lip type, for five (5) inches by eighteen (18) inches cowl vent.Width: 18.0 inches. Height: 5.0 inches.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Door Handle Gasket Set
p/n: 50-0193-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
U Jamb Lock Pillar Filler
p/n: 82-0064-79
This U Jamb Lock Pillar Filler seals the bottom of the rear side window, and may also be known as a door jamb seal.
Firewall Wiring Grommet
p/n: 25-0016-20
This Firewall Wiring Organizer Grommet is designed for original configuration and superior fit. Made from high-quality dense rubber to provide excellent durability.
Trunk Or Hatchback Weatherstrip
p/n: 82-0038-84
This Trunk Or Hatchback Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk or hatchback opening directly to the body.
Horn button contact cushion
p/n: 50-0409-21
Separator, horn contact. For standard or non-flexible wheel.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Door Hinge Seals
p/n: 70-1460-70
This Door Hinge Seal installs on the front door hinge pillar at the beltline. These seals are sold as a pair for the left and right side.
Radiator Bracket Cushion
p/n: 70-2070-31
Radiator support bracket, insulator, small type. See our #70-2050-31 for large type.Length: 4.5 inches.
Flexible Run Channel - 5ft
p/n: 70-1107-57
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft lengths.
Door Bumper
p/n: 34-0469-71
Bumpers, front door, upper. Approximately five eighths (5/8) inch square, three eighths (3/8) inch inside diameter. Steel core, retained by screw.
Radiator bracket cushion
p/n: 70-2050-31
Radiator support bracket, insulator, large type. See our #70-2070-31 for small type.
Heater control valve seal
p/n: 50-0347-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water.
Door Weatherstrip
p/n: 60-0114-73
Weatherstrip, door bottom, sponge constant section, solid skin surface, superior quality. Sold in six (6) foot strips only.Length: 72.0 inches.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Splash Apron / A-Arm / Radiator Dust Shield Set
p/n: 70-4679-45
This four (4) piece Splash Apron / A-Arm / Radiator Dust Shield Filler set is designed from the original part for superior fitment, finish, and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions.
GM Window Guide Assortment Set
p/n: 70-4729-62
A thirty (30) piece General Motors Window Guide Assortment Set with popular size coverage in a convenient and economic package. Assortment comes in convenient, translucent, durable polypropylene box.
Radiator Mounting Insulator Pads
p/n: 70-2238-31
A four (4) piece set of Radiator Mounting Insulator Pads. For use on all four corners of the radiator. For vehicle models with three (3) wide core radiators.
Trunk Weatherstrip
p/n: 82-0030-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Hood To Cowl Weatherstrip
p/n: 70-3420-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Outer Beltline Weatherstrip
p/n: 50-0466-61
This Outer Beltline Weatherstrip is fully molded with EPDM rubber over a corrosion resistant brass metal core. These window scrapers are for models with the chrome strip on the door.
Parking and Signal Gasket
p/n: 50-0354-16
Gasket, front parking and signal light to fender. One (1) pair per car. Fits between signal lamp body and headlamp to fender adapter.Width: 4.0 inches.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3161-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Fuel Neck Grommet
p/n: 50-0245-39
Grommet, fuel filler neck through rear apron. Fully molded rubber. Two and one fourth inch (2-1/4") inside length by three and three sixteenths inch (3-3/16") outside length.
Vent Window Division Post Seal
p/n: 70-3870-56
This Vent Window Division Post Seal is fully molded with metal core and attaching tabs.
Door Weatherstrip
p/n: 50-0219-73
This Door Weatherstrip is made of a high-quality sponge extrusion to original configuration. This weatherstrip is for the front door opening, lower front body hinge pillar.
Taillight Lens Gasket
p/n: 50-0197-15
Gasket, taillight lens, one fourth (1/4) inch thick sponge rubber.
Rumble Seat Step Mounting Pad
p/n: 70-0043-44
Pad, rumble seat step mounting for fender, double beaded edge per original. Width: 4.375 inches.
Taillight Lens Gasket
p/n: 70-1793-15
Gasket, taillight lens. Made of die cut sponge rubber to original configuration.