7/16" Door Weatherstrip
p/n: 70-0331-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. With its generic shape it has many uses outside of its original purpose. Available by the foot.
1" Floor Pan Plug
p/n: 35-0262-20
This Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Up to twelve (12) used per vehicle.
9/16" Wiring Grommet
p/n: 32-0352-20
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for the parking brake release rod.
3/4" Trunk Floor Pan Plug
p/n: 35-0070-87
This Trunk Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
Peel-N-Stick Door Edge Weatherstrip
p/n: 70-0390-WT
This Peel-N-Stick Door Edge Weatherstrip is designed for a specific set of vehicles but with its generic shape, has many uses outside of its original purpose. Available by the foot. Available by the foot.
3/4" Gearshift Grommet
p/n: 32-0050-24
This Gearshift Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed as an insulator for the gearshift control rod.
5/8" Wiring Grommet
p/n: 32-0366-53
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. Designed to run the windshield wiper control cable or gas gauge wire through the rear compartment pan.
7/16" Door Weatherstrip
p/n: 70-0390-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Clip Fastener - Door Weatherstrip
p/n: 60-0260-73
This Clip Fastener for Door Weatherstrips is made for a precise, factory like fit. Two (2) prong clip fastener with oval screw hole, made with spring steel and cadmium plated. Width: 7/8" inches. Height: 15/16 inches.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
Inner Side Window Bumper
p/n: 70-0775-62
Bumper, inner side window garnish molding. One (1) per door.Length: 1.0 inches. Width: .3125 inches. Height: .25 inches.
3/4" Hood and Door Bumper
p/n: 33-0459-42
This Hood and Door Bumper is fully molded and designed from the original part for superior fitment and seal. Designed for hood to cowl and door hinge pillar upper bumper. May be used in both places.
Fuel Filler Door Bumper
p/n: 33-0538-41
This Fuel Filler Door Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the Fuel Filler Door to support / cushion the closure and prevent metal to metal contact. Usually requires two (2) bumpers each per vehicle.
3/8" Inner Fender Bumper
p/n: 33-0512-44
Inner fender to inner splash pan bumper. This bumper is not a generic replacement, and will only be seen when inner fender is removed.
7/8" Trunk Bumper
p/n: 33-0293-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
1/2" Standard Bumper
p/n: 33-0496-71
This Standard Bumper is fully molded and designed from the original part for correct fitment and seal. Designed for applications such as door opening at upper corner, license plate, and fuel filler door. Self-retaining type bumper.
1-3/8" Wiring Grommet
p/n: 32-0369-20
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. Designed to run the wiring harness through the fender skirts or hood latch lower mounting panels.
7/8" Trunk Bumper
p/n: 33-0990-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.