Running Board Matting
p/n: 70-0420-49
Running board matting. Fully molded rubber strips with full length steel cores molded in.
Engine Mount Cushions
p/n: 70-0300-11
These Engine Mount Cushions are used as an intermediate engine mount for support bolts. Split in half if needed at installation. A four (4) piece set.
Rear Engine Support Pad
p/n: 70-0443-11
This Rear Engine Support Pad is used as a cushion at transmission. Makes a four (4) piece set after splitting.
Distributor boot
p/n: 70-0004-21
Boot, distributor dust and moisture. Original equipment, exact copy. V-16 only.
Hood Hinge Top Strap Pivot
p/n: 70-0045-42
A Hood Hinge Top Strap Pivot manufactured to OEM specifications to install for an authentic fit and finish. Cold rolled steel as original.
Windshield Weatherstrip Seal Set
p/n: 70-0015-52
This Windshield Weatherstrip Seal Set includes two (2) 15" Single-Flap side weatherstrip seals and one (1) 45" Double-Flat bottom weatherstrip seal. The set seals the windshield glass to the body and protects the interior of vehicle.
Hinge Pillar Weatherstrip
p/n: 70-0734-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Ferrule Installing Tool
p/n: 70-0662-69
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Convertible Top Rest Block
p/n: 70-0069-67
Pads, convertible top rest for rear deck. Two heights as original for inner and outer positions. Four (4) piece set.
Vacuum Clutch / Brake Cylinder Diaphragm
p/n: 50-0063-24
This Electromatic Clutch Control or Brake Vacuum Cylinder Diaphragm is designed from the original part for superior fitment and function. Used in different locations dependent upon vehicle make.
Rigid Run Channel
p/n: 70-0130-58
Special channel, felt lined rubber, for door upper front post for convertibles with cast upper post. Each piece sixteen (16) inches long.
Shock and stabilizer seal
p/n: 70-1185-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.
Windshield Weatherstrip Set
p/n: 70-0016-52
This three (3) piece Windshield Weatherstrip Set includes two 16-1/2" side weatherstrip channels and one 48" bottom weatherstrip channel. All corners are correctly molded to fit perfectly.
Hood bumper
p/n: 70-0013-42
Pads, hood hold-down clamp, mount on clamp swivels to hold hood corners in. Set of four (4) rubber pads in solid brass, chrome plated cups.
Front Apron Crossbar Grommets
p/n: 70-1131-45
This Front Apron Crossbar Grommet pair is designed from the original part for superior fitment, finish and function. Width: 3-1/2" inches. Height: 3-1/2" inches.
Body Mounting Pad
p/n: 70-0298-48
Pads, body mounting for front bracket, right and left. Three eighths (3/8) inch by two and three fourths (2-3/4) inch by four (4) inches with two (2) collars and retaining rings. Two (2) required per car.
Vacuum Brake Cylinder Rod Boot
p/n: 70-0010-24
This Vacuum Brake Cylinder Rod Boot is designed from the original part for superior fitment and seal. Made from durable rubber to original configuration.
Engine Mount Pad
p/n: 70-1162-11
This Front Engine Mount Pad pair is designed for cars with round cone type front engines. For V-12 and V-16 models.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Firewall Grommet Set
p/n: 70-1149-21
This Firewall Grommet Set contains six (6) pieces that are intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Shock and Stabilizer Seal
p/n: 70-1184-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set. Width: 1.1875 inches.
Front Bumper Grommet
p/n: 70-0103-28
Grommets, front bumper. Theses are for the round, tubular bumper support.
Hood Ventilator Bumper Set
p/n: 70-0011-42
This forty (40) piece Hood Ventilator Bumper set is designed from the original parts for superior fitment and function. The set includes bumpers and rivets for one (1) hood.
Side Mount Spare Grommet Set
p/n: 70-1136-37
This six (6) piece Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set can be used for various applications to support arms, brace rods, and cowl standoff posts.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Radiator Brace Filler Strip
p/n: 70-0020-31
Filler strip, radiator brace rods. Retains ignition wire and thermometer tube in hollow brace rods. Thirty (30) inch strips.
Windshield Gasket
p/n: 70-0078-52
This Windshield Gasket is made of a high-quality EPDM dense rubber extrusion. This four (4) foot weatherstrip mounts on the lower windshield.
Rear Window Gasket
p/n: 70-0018-83
This Rear Window Gasket comes in a seven foot, three inch (7' 3") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Taillight Gasket
p/n: 70-0258-15
Gaskets, taillight mounting under fender wire conduit base. Width: 3.25 inches.
Rumble Seat Step Mounting Pad
p/n: 70-0262-45
Pad, rumble seat step plate mounting, rectangle type for top of fender.Length: 4.875 inches. Width: 4.25 inches.
Headlight Stanchion Pad
p/n: 70-0255-21
Mounting pads, horn and headlight stanchion base to hood latch shelf. Two and one half (2-1/2) inches by four and one fourth (4-1/4) inches.Length: 4.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Golf Bag Door Weatherstrip
p/n: 70-0118-85
This Golf Bag Door Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts directly to the golf bag door.
Body Mounting Pad
p/n: 70-0299-48
Pad, body mounting, for body bracket. Two (2) collars and retaining rings. Four (4) per car.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Body Mounting Pad
p/n: 70-0297-48
Pad, body mounting. Three eighths (3/8) inch by two (2) inch by three (3) inch with collar and retainer ring.
Rumble Seat Lid Corner Pad
p/n: 70-0120-87
Pad, rumble seat lid corner, Compare with our #60-0191-87. Length: .75 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Body Mounting Pad
p/n: 70-0265-48
This Body to Frame Mounting Pad is designed from the original parts for superior fitment and function. Installs in metal bucket cups. Fully molded high quality EPDM rubber.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Brake shaft stop bumper
p/n: 70-0271-24
Bumper, brake rocker shaft lever stop. Two (2) used per car. Also used as door side bumper for some 1927-31 Cadillacs.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Door Bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Door Bumper
p/n: 70-1157-71
Pad, door jamb (door side bumper).Some bodies using escutcheons around pads.Length: 1.5625 inches. Width: 1.1875 inches.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Side Window Header Channel
p/n: 70-0306-58
Plush lined rubber channel for across top of doors above side windows on closed bodies. Available by the foot.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.