Door weatherstrip
p/n: 70-0525-73
Weatherstrip, rear door hinge pillar at beltline Two (2) per car. Two (2) piece set.
Battery Cable Grommet
p/n: 70-2318-20
Grommet, battery cable through radiator shroud. Reproduction of original rectangular design exactly. Replaces #1469080. Length: 2.4375 inches. Width: 1.5 inches.
Vent division bar weatherstrip
p/n: 60-0636-56
Front vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. See Front door vent weatherstrip for main rubber seal.
Rear Bumper End Filler Set
p/n: 70-3769-30
This four (4) piece Rear Bumper End Filler set is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Headlight Ring Gasket Set
p/n: 70-1465-14
This four (4) piece Headlight Ring Gasket Set is designed from the original part for superior fitment and seal. This gasket is for the headlight outer rim to sealed beam headlight retainer ring. Possible fit for models with dual headlights.
Hood Bumper
p/n: 70-0501-42
Bumpers, hood. Four (4) per set.Length: 1.4375 inches. Width: .5625 inches.
Front Inner Fender Seals at Rear
p/n: 70-2786-45
This Front Inner Fender Seal pair is designed from the original part for superior fitment and seal. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit at rear side of front inner fenders, making a Right and Left pair.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Rear Grill to Body Seal
p/n: 70-3124-31
This Rear Grill to Body Seal is designed from the original part for superior fitment and seal. This seal mounts on the top edge of REAR grill above the rear bumper.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Firewall Grommet
p/n: 70-0967-20
This Firewall Grommet is used to run the windshield washer, vacuum lines, antenna lead, and other wires through the firewall. Designed from the original part for superior fit and seal.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Firewall Grommet
p/n: 70-1012-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 70-0984-20
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
1-3/8" Firewall Grommet
p/n: 70-1013-20
This Firewall Grommet is used to run the speedometer cable through the firewall. Designed from the original part for superior fit and seal.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Fan Shroud Assembly Rubber
p/n: 70-2779-45
This two (2) piece Fan Shroud Assembly Rubber pair is designed from the original part for superior fitment and function. Shroud rubber is die cut from quality masticated rubber to authentic original dimensions. For models with Air Conditioning.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Fuel Filler Dust Shield
p/n: 70-2783-45
This Fuel Filler Dust Shield is designed from the original part for superior fitment and function. Shield piece is die cut from quality masticated rubber to authentic original dimensions. Shield fits around the fuel filler neck to body.
Door Lock Bumper
p/n: 70-0538-71
Bumper, door lock striker plate. Rubber with steel core, seven sixteenths (7/16) inch thick, one (1) per door. Installed in rotary latch receiver.
Wiring grommet
p/n: 70-0864-15
Grommet, taillight wiring through trunk inner panel. One (1) pair per car.
Front Stabilizer Bar End Link Set
p/n: 70-2109-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Directional Signal or Fog Light Lens Gaskets
p/n: 70-3093-17
This Directional Turn Signal or Fog Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Directional Signal / Fog Light Lens and the Directional Signal / Fog Light Housing or Bezel.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Upper Radiator Filler
p/n: 70-2784-45
This single piece Upper Radiator Filler is designed from the original part for superior fitment and function. This upper radiator to core support filler piece is die cut from quality masticated rubber to authentic original dimensions.
Taillight Lens Gaskets
p/n: 70-3229-15
This four (4) piece Taillight Lens Gasket set is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lamp lens & taillight housing.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Door Handle Gasket Set
p/n: 70-0925-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Weatherstrip
p/n: 70-1650-70
Seal, rear door at rear of window.Length: 1.75 inches. Width: .875 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Fog Light Inner Gaskets
p/n: 70-3331-17
This Fog Light Inner Gasket pair is designed from the original part for superior fitment and seal. Die cut from high quality 3/16" black sponge rubber to original specifications for a factory fit.
Directional and Parking Light Lens Gaskets
p/n: 70-3116-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Back Up Light Lens to Body Gaskets
p/n: 70-3119-17
This Back Up Light Lens to Body Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the back up light lens and the rear vehicle body.
License Plate Light Gasket
p/n: 70-3334-17
This License Plate Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the License Plate Light Lens and the License Plate Light Housing or Bezel.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Parking Brake Pedal Pad
p/n: 70-1273-22
Pad, parking brake locking pedal.Length: 2.0625 inches. Width: 1.5 inches.
Glovebox Door Link Grommet
p/n: 70-0968-88
This Glovebox Door Link Grommet is designed from the original part for superior fitment and function. Grommet works to cushion the glovebox door closure.
Interior Dome Light Lens Gasket
p/n: 70-3102-17
This Interior Dome Light Lens Gasket is designed from the original part for superior fitment and seal. This quality reproduction gasket fits between the interior dome light lens and the dome light housing or bezel.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Bumper Support Bar Pad
p/n: 70-0993-30
Bumper, impact bar end to body, for rear bumper. Fully molded rubber. Two inches (2") length by seven sixteenths inch (7/16") width by eleven sixteenths inch (11/16") height.
Body Mounting Pad
p/n: 50-0361-48
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Body Mounting Pad
p/n: 70-2233-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mount Isolator
p/n: 70-2232-48
Isolator, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.