Taillight Lens Gaskets
p/n: 70-3229-15
This four (4) piece Taillight Lens Gasket set is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lamp lens & taillight housing.
Upper Radiator Filler
p/n: 70-2784-45
This single piece Upper Radiator Filler is designed from the original part for superior fitment and function. This upper radiator to core support filler piece is die cut from quality masticated rubber to authentic original dimensions.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Directional Signal or Fog Light Lens Gaskets
p/n: 70-3093-17
This Directional Turn Signal or Fog Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Directional Signal / Fog Light Lens and the Directional Signal / Fog Light Housing or Bezel.
Front Stabilizer Bar End Link Set
p/n: 70-2109-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Wiring grommet
p/n: 70-0864-15
Grommet, taillight wiring through trunk inner panel. One (1) pair per car.
Roof Rail Filler
p/n: 70-1763-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Bumper To Inner Fender Seals
p/n: 70-2781-45
This Bumper To Inner Fender Seal pair is designed from the original part for superior fitment and function. Filler shield pieces are die cut from quality masticated rubber to authentic original dimensions.
Fuel Filler Dust Shield
p/n: 70-2783-45
This Fuel Filler Dust Shield is designed from the original part for superior fitment and function. Shield piece is die cut from quality masticated rubber to authentic original dimensions. Shield fits around the fuel filler neck to body.
Door Handle Gasket Set
p/n: 70-0979-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Fan Shroud Assembly Rubber
p/n: 70-2779-45
This two (2) piece Fan Shroud Assembly Rubber pair is designed from the original part for superior fitment and function. Shroud rubber is die cut from quality masticated rubber to authentic original dimensions. For models with Air Conditioning.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
1-3/8" Firewall Grommet
p/n: 70-1013-20
This Firewall Grommet is used to run the speedometer cable through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 70-0984-20
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 70-1012-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from the original part for superior fit and seal.
Steering Column Finish Strip
p/n: 70-1031-88
Seal, steering column to instrument panel. Extruded rubber twelve (12) inch strip to exact cross-section.Length: 10.5 inches. Width: .50 inches.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Firewall Grommet
p/n: 70-0967-20
This Firewall Grommet is used to run the windshield washer, vacuum lines, antenna lead, and other wires through the firewall. Designed from the original part for superior fit and seal.
Windshield Post to Door Seal
p/n: 70-0304-73
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Rear Wheelhouse Seals
p/n: 70-2782-45
This Rear Wheelhouse Seal pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Rear Grill to Body Seal
p/n: 70-3124-31
This Rear Grill to Body Seal is designed from the original part for superior fitment and seal. This seal mounts on the top edge of REAR grill above the rear bumper.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
A-Arm Dust Shields Filler
p/n: 70-2772-45
This two (2) piece A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms only.
Front Inner Fender Seals at Rear
p/n: 70-2786-45
This Front Inner Fender Seal pair is designed from the original part for superior fitment and seal. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit at rear side of front inner fenders, making a Right and Left pair.
Hood Bumper
p/n: 70-0501-42
Bumpers, hood. Four (4) per set.Length: 1.4375 inches. Width: .5625 inches.
Parking Light Lens Gasket
p/n: 70-1081-16
Gasket, fog and parking light lens housing.Length: 8.5 inches. Width: 4.0 inches.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Headlight Ring Gasket Set
p/n: 70-1465-14
This four (4) piece Headlight Ring Gasket Set is designed from the original part for superior fitment and seal. This gasket is for the headlight outer rim to sealed beam headlight retainer ring. Possible fit for models with dual headlights.
Side Window Vertical Leading Edge
p/n: 70-0815-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Rear Bumper End Filler Set
p/n: 70-3769-30
This four (4) piece Rear Bumper End Filler set is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Vent Window Division Bar Weatherstrip
p/n: 70-0703-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent division bar weatherstrip
p/n: 60-0636-56
Front vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. See Front door vent weatherstrip for main rubber seal.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Vent Division Bar Weatherstrip
p/n: 70-0922-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Upper Lock Pillar Filler
p/n: 70-0782-79
A fully molded Upper Lock Pillar Filler pair. One and five eighths inch (1-5/8") wide and two- and three-quarter inches (2-3/4") high. This part seals the bottom of the rear side window and may also be known as a door jamb seal.
Battery Cable Grommet
p/n: 70-2318-20
Grommet, battery cable through radiator shroud. Reproduction of original rectangular design exactly. Replaces #1469080. Length: 2.4375 inches. Width: 1.5 inches.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rear Bumper To Body Filler
p/n: 70-3078-30
This Rear Bumper To Body Filler is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. This piece fits between the rear bumper and the vehicle body.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Air Conditioning Pipe Grommet
p/n: 70-0934-31
Grommet, air conditioning pipes to compressor and condenser. One (1) per car.Length: 4.375 inches. Width: 2.5 inches.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
1957-1958 Cadillac Factory Shop Manual, CD
p/n: 07-1057-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory shop repair manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
1959-1960 Cadillac Factory Shop Manual, CD
p/n: 07-1058-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory shop repair manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Front Door Hinge Pillar Weatherstrips
p/n: 60-0326-73
This Front Door Hinge Pillar Weatherstrip set fits at the front door opening. Auxiliary on door hinge pillar at beltline, right and left. Sometimes called "L" or "J" strips. Fully molded with authentic configuration to help guide water to the outside of vehicle.
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
Front Door Auxiliary Weatherstrips
p/n: 70-0551-73
This Front Door Auxiliary Weatherstrip pair fits to the left and right doors at the beltline. Uses snap-in fasteners, four (4) each included.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Hood to Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Axle Rebound Pad
p/n: 70-2225-32
Bumper, rear spring axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.
Fog light lens gasket
p/n: 70-3106-16
Gasket set, front turn signal and fog light lens. Four (4) piece set.
Steering Column Grommet
p/n: 70-2316-88
Grommet, steering column at floor. Order our #70-2316-88 seal separately.
Radiator to Support Filler
p/n: 70-2780-45
This four (4) piece Radiator to Support Filler set is designed from the original part for superior fitment and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. For models with Air Conditioning.
Hood to Cowl Weatherstrip
p/n: 70-0827-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood To Cowl Weatherstrip
p/n: 70-1019-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Steering Column Floorplate
p/n: 70-1425-88
Seal, steering column to firewall. For 1956 vehicles purchase our #70-1509-88 grommet separately. For 1957-58 vehicles purchase our #70-2316-88 grommet separately.
Quarter Window U Jamb Lock Pillar Fillers
p/n: 70-0923-79
This Quarter Window U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
U Jamb lock pillar filler
p/n: 50-0269-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Axle Rebound Pad
p/n: 70-2591-32
Bumper, air suspension rear axle impact. Located on frame rail. Rubber only, does not include metal retaining clips or bolts.
Front Suspension Bumper
p/n: 70-2649-35
This Front Suspension Bumper pair for the Lower A-arm is made from 100% EPDM dense rubber for durability. Fully molded with integral mounting bolt.
Hinge Pillar Weatherstrip
p/n: 70-1523-73
Weatherstrip, upper front door hinge pillar at roof rail. Molded as left and right with corrosion resistant brass metal core.
Upper Suspension Arm Dust Seal
p/n: 70-0890-32
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Taillight Gasket Kit
p/n: 70-0972-15
Gasket set, taillight and backup light assembly to fender. Four (4) piece set.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-2493-45
This six (6) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-2494-45
This ten (10) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Hood to Cowl Side Extension Filler
p/n: 70-2258-43
This Hood to Cowl Side Extension Filler pair is fully molded from soft EPDM sponge rubber with all original details.
Defroster Vent Gasket
p/n: 70-2279-31
Gasket, defroster vent at base of windshield. One (1) pair required per car.
Air Intake Scoop Mounting Pad
p/n: 70-2022-31
Pad, air conditioning air intake (scoop) mounting.Length: 6.375 inches.
Trunk Weatherstrip
p/n: 70-0896-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Cadillac Master Parts List 1957 - 1964 (Reprint)
p/n: 07-1443-07
This 1957-1964 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems.
Engine Mount Service – Revulcanization Only
p/n: 70-0674-11
This Revulcanization Service Only is designed to restore your Rear Engine Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 70-0629-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Cadillac Master Parts List 1948 - 1959 (Reprint)
p/n: 07-1442-07
This 1948-1959 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems.
Front Door Weatherstrips
p/n: 70-0745-72
This Front Door Weatherstrip pair is the primary door to body weatherstrips. It has molded ends and includes 6 pins and 24 sockets for easy installation. Made of top-quality rubber.
Front Door Vent Window Weatherstrips
p/n: 38-0071-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Windshield Gasket
p/n: 70-0671-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Prop shaft support service
p/n: 70-0748-27
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
Hardtop Roof Rail Weatherstrips
p/n: 70-0611-68
These Hardtop Roof Rail Weatherstrips fit on the roof of the vehicle and seal the side windows when the window is fully raised.
Door Weatherstrip
p/n: 70-0544-73
Weatherstrip, front door opening, auxiliary on cowl at beltline. Right and left, brass core.
Rear Window Gasket
p/n: 60-0498-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. This is for vehicles with the upper inside garnish molding.
Harmonic balancer service
p/n: 70-1047-12
Engine harmonic balancer. Revulcanization service only. Send in your old, rebuildable balancer and pulley assembly.
Rear Window Gasket
p/n: 70-0699-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.