Rear Stabilizer Bushing
p/n: 70-0406-33
Bushings, rear stabilizer. Comes as a four (4) piece set. Fully molded rubber.
Windshield Division Bar Gasket
p/n: 70-0277-51
This inner and outer Windshield Division Bar Gasket is designed from the original part for superior fitment and function. This windshield center divider is molded with pilots and screw holes. Without a steel core.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Fuel Neck Grommet
p/n: 70-0090-39
Grommet, fuel filler neck. Off center flange style. Fully molded rubber.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Clutch or Brake Pedal Pad - Brown
p/n: 70-0176-89
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Front Stabilizer Bushing
p/n: 70-0193-33
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Fuel Neck Grommet
p/n: 70-0599-39
Grommet, fuel filler neck, through rear fender splash panel. Fully molded rubber. Four and five eighths inch (4 5/8") outside diameter by two and three sixteenths inch (2 3/16") inside hole diameter.
Rear Gravel Deflector to Bumper Face Bar
p/n: 70-0462-45
This Rear Gravel Deflector to Bumper Face Bar staples to the gravel deflector. The seal is die cut from dense rubber. Sold as a six (6) foot strip.
Rear Quarter Window Bumper
p/n: 70-0688-62
Bumper, rear quarter window on door lock pillar. One and one fourth (1-1/4) inch square with metal core. Two (2) per car.Length: 1.375 inches.
Trunk Bumper
p/n: 50-0163-87
Bumper, trunk. Brass core, screw held. Two (2) per car.Length: 1.5 inches. Width: .75 inches.
Front Stabilizer Bushing
p/n: 70-0717-33
Bushing, front stabilizer bar to frame.Length: 1.875 inches. Width: .6875 inches. Height: 1.625 inches.
Handbrake Pull Rubber Grip
p/n: 70-0385-24
Rubber grip, handbrake pull. This was an optional item alternating with a chrome handle.
Accelerator Pedal Pad
p/n: 70-0208-40
Pad, accelerator pedal. Black rubber. For brown see our #70-0208-89. Made to slip over old metal core after removing old rubber. Length: 8.25 inches.
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Accelerator Pedal Pad
p/n: 70-0275-40
Pad, accelerator pedal, full slipover type, fits over old metal after removing original rubber. Length: 8.5 inches.
Folding Seat Bumper
p/n: 70-2576-88
Bumper, front seat back center arm hinge. Excellent finish and details with original style metal core. Both seat back inner corners rest on this single bumper.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Fuel Neck Grommet
p/n: 70-0091-39
Grommet, fuel filler neck. Saddle style. Three and three eighths inch (3-3/8") outside width by three and five eighths inch (3-5/8") outside length by two and one fourth inch (2-1/4") inside hole diameter by one and one fourth inch (1-1/4") height.