Vent division bar weatherstrip
p/n: 70-0696-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Division Bar Weatherstrip
p/n: 70-0800-56
This Front Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs.
Vent division bar weatherstrip
p/n: 70-0821-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent division bar weatherstrip
p/n: 70-0791-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Vent Window Division Post Weatherstrips
p/n: 60-0569-56
This Front Window Vent Division Post Weatherstrip pair is fully molded with metal core and attaching tabs.
Wheel Cover Cushion
p/n: 70-0633-38
Filler, wheel cover to wheel. Approximately two and one eighth (2-1/8) inches long each, twenty (20) required per car. (Five (5) per wheel cover).
Window Channel Retaining Clip
p/n: 70-0515-62
Clip, side window run channel retaining. Rust resistant spring steel.
Window Channel Retaining Clip
p/n: 70-0514-62
Clip, side window run channel retaining. Rust resistant spring steel. Compare with your original.
Window Felt and Run Channel Set
p/n: 90-0142-58
This six (6) piece Window Felt and Run Channel set includes the inner and outer window felts and the flexible run channels needed to complete two (2) doors. This set is used for front or rear doors in models without vent windows in the door.
Window Felt and Run Channel Set
p/n: 90-0140-58
This eight (8) piece Window Felt and Run Channel set includes the inner and outer window felts, upper rigid run channels, and flexible run channels needed to complete two doors. The set can be used for front or rear doors in models with vent windows in the door.
Window Felt and Run Channel Set
p/n: 90-0141-58
This ten (10) piece Window Felt and Run Channel set includes the inner and outer window felts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
Windshield Division Bar Gasket
p/n: 70-0277-51
This inner and outer Windshield Division Bar Gasket is designed from the original part for superior fitment and function. This windshield center divider is molded with pilots and screw holes. Without a steel core.
Windshield Division Bar Gasket
p/n: 70-0372-51
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part is properly sized with "H" section. Part requires fitting to top and bottom, as it is not drilled.
Windshield Division Bar Gasket
p/n: 70-0309-51
Gaskets, windshield division channel, inner and outer, fully molded to include bolt holes and pilots. Two (2) piece set.
Windshield Division Bar Gasket
p/n: 70-0159-51
This inner and outer Windshield Division Bar Gasket acts as a retainer for the outer division bar chrome molding.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Windshield Gasket
p/n: 70-0526-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. This seal has molded sections for the wiper transmissions and the slot to accommodate the outer edge molding.
Windshield Gasket
p/n: 70-0535-50
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Windshield Gasket
p/n: 70-0524-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Windshield Gasket
p/n: 70-0512-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. This seal has molded sections for the wiper transmissions and the slot to accommodate the outer molding.
Windshield Gasket
p/n: 70-0566-50
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Windshield Gasket
p/n: 70-0715-50
This Windshield Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required.
Windshield Gasket
p/n: 70-0602-50
This Windshield Gasket mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Windshield Gasket Set
p/n: 70-0615-50
This Windshield Gasket Set mounts around the full perimeter of the front glass and has the divider bar molded directly into it. It has properly molded corners to precisely conform to the glass and molded sections for the wiper transmissions.
Windshield Gasket Set
p/n: 70-0460-50
This Windshield Gasket Set contains the windshield gasket itself and the locking strip. The seal mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Wiper control grommet
p/n: 60-0197-53
Grommet, wiper control connection link. Replaces #4161287. 11/32" I.D. X 19/32" O.D.
Wiper Transmission Gasket
p/n: 70-0499-53
Gasket, wiper transmission mounting. Replaces #4089635 for smaller type wiper gear, about 7/8" X 1-1/8". Early series models only.
Wiper Transmission Gasket
p/n: 70-1198-53
Gasket, windshield wiper transmission (1939-later type). Replaces #4097038.
Wiring Grommet
p/n: 70-0355-14
This Wiring Grommet is used to run electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fully molded from top-quality EPDM dense rubber to provide excellent durability.