Front Engine Support
p/n: 70-0276-11
This Front Engine Support is designed from original parts for an exact reproduction. Constructed of rubber and steel for proper engine vibration isolation.
Door Weatherstrip
p/n: 70-0085-73
Weatherstrip, door opening, fits retainer under edge of body sill to form seal when door is closed. Six (6) foot strips.Length: 72.0 inches. Width: 1.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Rear Bumper Grommet
p/n: 70-0144-29
Grommets, rear bumper (Some cars have this type, some have our #70-0164-29, sold separately. They are both interchangeable and original). Fully molded rubber.
Cadillac V-8 Pedal Pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Taillight Mounting Pad
p/n: 70-0316-15
Pads, taillight mounting, right and left, top grade workmanship and material.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Rear Bumper Grommet
p/n: 70-0164-29
Grommets, rear bumper. (Some cars have this type, some have our #70-0144-29, sold separately. They are both interchangeable and original). Fully molded rubber.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Rear window division bar seal
p/n: 70-0068-82
Seal, rear window divider, inner and outer for two (2) and three (3) light rear windows, two (2) piece set for one (1) division bar.
Windshield Division Bar Gasket
p/n: 70-0159-51
This inner and outer Windshield Division Bar Gasket acts as a retainer for the outer division bar chrome molding.
Rear Stabilizer Bushing
p/n: 70-0406-33
Bushings, rear stabilizer. Comes as a four (4) piece set. Fully molded rubber.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Front Stabilizer Bushing
p/n: 70-0717-33
Bushing, front stabilizer bar to frame.Length: 1.875 inches. Width: .6875 inches. Height: 1.625 inches.
Handbrake Pull Rubber Grip
p/n: 70-0385-24
Rubber grip, handbrake pull. This was an optional item alternating with a chrome handle.
Accelerator Pedal Pad
p/n: 70-0275-40
Pad, accelerator pedal, full slipover type, fits over old metal after removing original rubber. Length: 8.5 inches.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Fuel Neck Grommet
p/n: 70-0091-39
Grommet, fuel filler neck. Saddle style. Three and three eighths inch (3-3/8") outside width by three and five eighths inch (3-5/8") outside length by two and one fourth inch (2-1/4") inside hole diameter by one and one fourth inch (1-1/4") height.
Fuel Neck Grommet
p/n: 50-0067-39
Grommet, fuel filler neck. Oblong fully molded rubber. Two and one eighths inch (2-1/8") inch inside length by three and one half inch (3-1/2") outside diameter by three and three fourths inch (3-3/4") outside length.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Brake and clutch shank seal
p/n: 70-0156-23
Grommet, brake and clutch pedal shank at toe board. Flange retained, perfect copy.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft.
p/n: 70-1097-44
Fender Welting is typically used to attach two (2) fenders to body. A superior quality, proper construction of reinforced black vinyl over vinyl core. Measures one and three eighths (1-3/8) inch wide. Twenty-five (25') foot roll of one-fourth (1/4") inch bead.
Fender Welting with 3/16 Bead - 25ft.
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a twenty-five (25') foot roll.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Antenna Boot
p/n: 70-0212-21
This Antenna Boot is designed from the original part for superior fitment and function. This boot fits at the vehicle running board antenna wire connection.
2-7/16" Firewall Grommet
p/n: 70-0621-20
This Firewall Grommet is used to run the cowl vent drain hose and throttle control cable through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 70-1203-20
This Firewall Grommet is used to run various electrical and dash gauge wires through the firewall. Also see our 32-1201-20 and 32-0225-20.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Spare Tire Bumper
p/n: 70-0126-37
Rest pad, spare wheel cover, metal core, screw held type. Eight (8) required per car.Width: 1.75 inches. Height: 1.4375 inches.
Spare Tire Bumper
p/n: 70-0125-37
Rest pad, spare wheel cover, metal core, tab held type. Sixteen (16) required per car.Width: 1.75 inches. Height: .75 inches.
Glovebox Door Check Grommet
p/n: 70-0285-88
Grommet, glovebox door check link, for one and one eighth (1-1/8) inches slot in dash.Length: 1.4375 inches. Width: .625 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Lower suspension arm dust seal
p/n: 70-0625-32
Dust seal, lower suspension arm bushing. Four (4) required per car.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
Body Mounting Pad
p/n: 70-0235-48
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Body Mounting Pad
p/n: 50-0131-48
Pad, body mounting. Fully molded rubber with locating collar. Two-inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter.