Firewall Grommet
p/n: 70-0984-20
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
Rear Quarter Window Bumper
p/n: 70-1096-62
Bumper, rear quarter window. Made of molded neoprene rubber with steel washer core. Two (2) per car.Length: 1.0625 inches.
Brake and clutch shank seal
p/n: 70-0466-23
Grommet, brake and clutch pedal shank above floorboard. Special offset pattern as original.
Taillight Lens Gasket
p/n: 70-0951-15
Gasket, taillight lens. Die cut one eighth (1/8) inch sponge rubber. Note: Sixty Special (60 Special) will require two (2) pairs.
Brake and Clutch Shank Seal
p/n: 70-0962-23
Grommet, brake or clutch shaft at toe board.Height: 1.0 inches.
Trunk Hinge Mounting Pad
p/n: 70-1231-87
Mounting pads, trunk hinge. Four (4) piece set.Length: 8.8125 inches.
Hydraulic Window Lift Grommet
p/n: 70-0642-21
Grommet, window lift hydraulic line through floor panel. Single hole type (for two (2) hole type, see our #70-0643-21).Length: 1.5 inches. Width: 1.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Exhaust System Hanger
p/n: 70-0626-13
Insulator (hanger) tailpipe to frame. See also our #70-0600-13.Length: 3.9375 inches. Width: 1.9375 inches.
Firewall Grommet
p/n: 70-1012-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from the original part for superior fit and seal.
Center Division Bar Chrome Molding Retainer
p/n: 70-0373-51
Center Division Bar Chrome Molding Retainer for outside windshield center post stainless molding. Use with original stainless molding and clips. Length: 15-1/2 inches. Width: 1-1/4 inches.
2-7/16" Firewall Grommet
p/n: 70-0621-20
This Firewall Grommet is used to run the cowl vent drain hose and throttle control cable through the firewall. Designed from the original part for superior fit and seal.
2-7/16" Firewall Grommet
p/n: 70-0622-20
This Firewall Grommet is used to run the wiring harness, oil pressure tube, windshield wiper tube, capillary tube, and radio antenna wire through the firewall. Designed from the original part for superior fit and seal.
Trunk Handle Mounting Pad
p/n: 70-0647-86
Mounting pad, trunk handle and lock escutcheon plate.Length: 2.875 inches. Width: 1.625 inches.
Steering Column Finish Strip
p/n: 70-1707-88
Seal, steering column to instrument panel. Extruded rubber strip thirteen (13) inch to exact cross-section.Length: 13.0 inches. Width: .625 inches.
Steering Column Finish Strip
p/n: 70-1031-88
Seal, steering column to instrument panel. Extruded rubber twelve (12) inch strip to exact cross-section.Length: 10.5 inches. Width: .50 inches.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
2-3/8" Firewall Grommet
p/n: 70-0350-20
This Firewall Grommet is used to run the coil wire thermometer tube through the firewall. Designed from the original part for superior fit and seal.
Door Lock Weatherstrip
p/n: 50-0172-70
Weatherstrip, door lock, front and rear. Protects door lock mechanism from dust and weather.Length: 3.625 inches.
2-3/8" Firewall Grommet
p/n: 70-0185-20
This Firewall Grommet is used to run the main wiring harness in addition to five (5) accessory wires through the firewall. Designed from the original part for superior fit and seal.
Taillight Gasket
p/n: 70-0900-15
Gasket, taillight housing. Also order #70-0471-15 for the taillight mounting pad, and for the taillight lens gasket order #70-0658-15. Length: 8.25 inches.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Body / Cowl to Fender Seals
p/n: 70-2787-43
This Body / Cowl to Fender Seals pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Firewall Grommet
p/n: 70-0967-20
This Firewall Grommet is used to run the windshield washer, vacuum lines, antenna lead, and other wires through the firewall. Designed from the original part for superior fit and seal.
Windshield Post to Door Seal
p/n: 70-0304-73
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Rear Wheelhouse Seals
p/n: 70-2782-45
This Rear Wheelhouse Seal pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3060-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Steering Column Gasket
p/n: 70-2317-88
Insulator, steering column lower mounting frame gasket. Triangular shape with mounting holes and column tube clearance.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Firewall Grommet
p/n: 70-0554-20
This Firewall Grommet is a special rectangular, two (2) hole grommet, that is used on the left side of the cowl the run the hydraulic line through the sheet metal.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Brake and clutch shank seal
p/n: 70-0465-23
Grommets, brake and clutch pedal shank below floorboard.
Rear Grill to Body Seal
p/n: 70-3124-31
This Rear Grill to Body Seal is designed from the original part for superior fitment and seal. This seal mounts on the top edge of REAR grill above the rear bumper.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3059-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Cowl Vent Hose
p/n: 60-0457-54
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
A-Arm Dust Shields Filler
p/n: 70-2772-45
This two (2) piece A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms only.
Door Bumper
p/n: 34-0469-71
Bumpers, front door, upper. Approximately five eighths (5/8) inch square, three eighths (3/8) inch inside diameter. Steel core, retained by screw.
Door Hinge Seals
p/n: 70-1460-70
This Door Hinge Seal installs on the front door hinge pillar at the beltline. These seals are sold as a pair for the left and right side.
Door Weatherstrip
p/n: 60-0114-73
Weatherstrip, door bottom, sponge constant section, solid skin surface, superior quality. Sold in six (6) foot strips only.Length: 72.0 inches.
Hydraulic Pump Grommet
p/n: 70-0640-21
Grommet, two (2) hole, for hydraulic pump through sheet metal.Length: 1.9375 inches. Width: 1.125 inches.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Door Weatherstrip
p/n: 50-0219-73
This Door Weatherstrip is made of a high-quality sponge extrusion to original configuration. This weatherstrip is for the front door opening, lower front body hinge pillar.
Front Inner Fender Seals at Rear
p/n: 70-2786-45
This Front Inner Fender Seal pair is designed from the original part for superior fitment and seal. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit at rear side of front inner fenders, making a Right and Left pair.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Firewall Grommet
p/n: 70-0949-20
This Firewall Grommet is used to run the heater lines to the control valve. Designed from the original part for superior fit and seal.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Trunk Hinge Mounting Pad
p/n: 70-1229-87
Mounting pad, trunk hinge. Four (4) piece set.Length: 7.625 inches.
Convertible Top Front Bow Weatherstrip
p/n: 70-0100-64
This Convertible Top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the top of the windshield.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Bumper Seal
p/n: 70-0978-45
Filler valance or deflector, rear. Extruded rubber to correct cross section. Fifty five (55) inches long.Length: 55.0 inches. Height: .28125 inches.
Side Window Vertical Leading Edge
p/n: 70-0832-80
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Headlight & Cornering Light Filler Seal Set
p/n: 70-2788-14
This six (6) piece Headlight & Cornering Light Filler Seal Set is designed from the original part for superior fitment and seal. These pieces fit behind the cornering lights.
U Jamb Door Lock Pillar Fillers
p/n: 70-0877-79
This quarter window U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
Hood bumper
p/n: 70-0543-42
Bumpers, hood to fender. Mounted on hood, rubber with steel core. Replaces Bakelite originals which are not available.
Hood Bumper
p/n: 70-0501-42
Bumpers, hood. Four (4) per set.Length: 1.4375 inches. Width: .5625 inches.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Door Conduit
p/n: 70-0828-21
Conduit, hydraulic line & power window wire. Front doors only. 2 pieces cut nine and one half (9-1/2) inches.Length: 9.50 inches. Height: 1.50 inches.
Body to door conduit
p/n: 70-0506-21
Conduit (double rubber hose), body to door, for hydraulic and electrical lines to power window.