Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Spare Tire Bumper
p/n: 70-0125-37
Rest pad, spare wheel cover, metal core, tab held type. Sixteen (16) required per car.Width: 1.75 inches. Height: .75 inches.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Taillight Lens Gaskets
p/n: 70-3229-15
This four (4) piece Taillight Lens Gasket set is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lamp lens & taillight housing.
Glovebox Door Check Grommet
p/n: 70-0467-88
Grommet, glovebox door check link, for one (1) inch slot in dash.
Upper Radiator Filler
p/n: 70-2784-45
This single piece Upper Radiator Filler is designed from the original part for superior fitment and function. This upper radiator to core support filler piece is die cut from quality masticated rubber to authentic original dimensions.
Hood Rest Pad
p/n: 70-0150-42
Pad, hood rest, molded to brass core, screw mounted.Width: 1.75 inches.
Directional & Parking Light Lens Gaskets
p/n: 70-3092-16
This Directional Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the signal / parking light lens and the signal / parking light housing or bezel.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Phototube Mounting Pad
p/n: 70-0721-17
Pad, phototube mounting on instrument panel. Automatic headlight beam control.Length: 2.3125 inches. Width: 1.6785 inches.
Taillight Lens Gaskets - In Bumper Ends
p/n: 70-4923-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens and taillight housing bezel in each bumper end.
Spare Tire Bumper
p/n: 70-0126-37
Rest pad, spare wheel cover, metal core, screw held type. Eight (8) required per car.Width: 1.75 inches. Height: 1.4375 inches.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Directional Signal or Fog Light Lens Gaskets
p/n: 70-3093-17
This Directional Turn Signal or Fog Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Directional Signal / Fog Light Lens and the Directional Signal / Fog Light Housing or Bezel.
Firewall Grommet
p/n: 70-1089-20
This Firewall Grommet is used to run the heater hose through the firewall. Designed from the original part for superior fit and seal.
Door Check Link Rod End Stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
Front Stabilizer Bar End Link Set
p/n: 70-2109-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Wiring grommet
p/n: 70-0864-15
Grommet, taillight wiring through trunk inner panel. One (1) pair per car.
1-1/2" Firewall Grommet
p/n: 70-0186-20
This Firewall Grommet is used to run the vacuum operated radio antenna lines through the firewall. Designed from the original part for superior fit and seal.
Front Bow Weatherstrip
p/n: 70-0785-64
Weatherstrip, front bow of convertible. Sponge rubber extrusion of correct dimensions.Length: 60.0 inches. Width: .8125 inches.
Body / Cowl to Fender Seals
p/n: 70-2790-43
This Body / Cowl to Fender Seals pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Radiator Upper Support Filler
p/n: 70-2502-45
This single piece Radiator Upper Support Filler is designed from the original part for superior fitment and function. Filler piece is die cut from quality masticated rubber to authentic original dimensions. Fits at radiator to radiator upper support.
Roof Rail Filler
p/n: 70-1763-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes.
Front Stabilizer Bar End Link Set
p/n: 70-2110-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Brake Pedal Pad
p/n: 70-1095-22
Pad, brake pedal. Fully molded duplicate of original pattern.Length: 3.75 inches. Width: 2.4375 inches.
Fuel Filler Dust Shield
p/n: 70-2783-45
This Fuel Filler Dust Shield is designed from the original part for superior fitment and function. Shield piece is die cut from quality masticated rubber to authentic original dimensions. Shield fits around the fuel filler neck to body.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Bumper To Inner Fender Seals
p/n: 70-2781-45
This Bumper To Inner Fender Seal pair is designed from the original part for superior fitment and function. Filler shield pieces are die cut from quality masticated rubber to authentic original dimensions.
Hood to Fan Shroud Seal
p/n: 70-2789-43
This Hood To Fan Shroud Seal is designed from the original part for superior fitment and function. Attaches to bottom side of hood. This seal piece is die cut from quality masticated black rubber to authentic original dimensions.
Door Handle Gasket Set
p/n: 50-0494-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Firewall Grommet
p/n: 70-1203-20
This Firewall Grommet is used to run various electrical and dash gauge wires through the firewall. Also see our 32-1201-20 and 32-0225-20.
Door Handle Gasket Set
p/n: 70-0979-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Inner Fender Seal
p/n: 70-0817-45
Filler, rear bumper gravel deflector. Die cut masticated sheet rubber. Approximately eleven (11) inches overall long.
1-13/16" Firewall Grommet
p/n: 70-0453-20
This Firewall Grommet is a four (4) hole design that is used for the hood release, vacuum antenna tube, and others. Designed from the original part for superior fit and seal.
Convertible Weatherlip
p/n: 70-0616-67
Weather deflector, edge of folding top fabric near folding post, mounted on body.
Fan Shroud Assembly Rubber
p/n: 70-2779-45
This two (2) piece Fan Shroud Assembly Rubber pair is designed from the original part for superior fitment and function. Shroud rubber is die cut from quality masticated rubber to authentic original dimensions. For models with Air Conditioning.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
1-3/8" Firewall Grommet
p/n: 70-1013-20
This Firewall Grommet is used to run the speedometer cable through the firewall. Designed from the original part for superior fit and seal.
Bumper Seal
p/n: 70-0563-45
Filler valance or deflector, rear. Eight (8) inches long (cut shorter where required), three (3) to four (4) required per car.
Hydraulic Window Lift Grommet
p/n: 70-0643-21
Grommet, window lift hydraulic lines through floor panel, 2-hole style (for cars requiring single-hole style, see our #70-0642-21).Length: 1.5 inches.