Front Door weatherstrip
p/n: 90-0134-72
Door edge weatherstrip with molded corners. This part is the primary door to body weatherstrip. Adhesive is not included in the kits.
Front Door Weatherstrips
p/n: 90-0108-72
This four (4) piece Front Door Weatherstrip Set is the primary weatherstrip for the door to the body. Set includes the door edge weatherstrip with molded corners and hinge post weatherstrip.
Front Fender Dust Shield Clip
p/n: 70-0681-44
This Front Fender Dust Shield Clip is designed from spring tempered wire, to original configuration. Up to sixteen (16) per car required.
Front Fender Dust Shield Seal
p/n: 70-0581-45
This Front Fender Dust Shield works as a shield to radiator air deflector. Sold as a pair for the right and left side.
Front Fender Shield Filler
p/n: 70-0680-44
This six (6) piece Front Fender Shield Filler is the front fender dust shield for the inner fender to frame including over upper control arm and around battery. Die cut from cotton reinforced sheet rubber.
Front Spring Bumpers - Lower Suspension Arms
p/n: 70-0172-32
This Front Spring Bumpers pair is designed from the original part for an authentic fit, finish, and appearance. These front spring bumpers install to the lower suspension arms. An original copy reproduction.
Front Stabilizer Bushing
p/n: 70-0193-33
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Front Stablizer Bar End Link Kit
p/n: 70-0574-33
Kit, front stabilizer bar link assembly replacement. Twenty two (22) piece set for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 8-7/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Fuel Filler Cover Bumper
p/n: 33-0557-15
Bumper, taillight body upper half and fuel filler cover to lower half. Four (4) per set. Length: 13/16 inches. Width: 1/2 inches.
Fuel Neck Grommet
p/n: 70-0599-39
Grommet, fuel filler neck, through rear fender splash panel. Fully molded rubber. Four and five eighths inch (4 5/8") outside diameter by two and three sixteenths inch (2 3/16") inside hole diameter.
Glovebox Link Bumper
p/n: 70-1459-88
Bumper, glovebox check link. Fits on glovebox door arm as needed.Length: .75 inches. Width: .3125 inches. Height: .4375 inches.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hood Bumper
p/n: 70-0409-42
Bumpers, hood top panel at cowl. One half (1/2) inch by one half (1/2) inch by three and one fourth (3-1/4) inch. Held in place by screws. Two (2) to four (4) per car as required.
Hood rest pad
p/n: 70-0139-42
Pad, hood rest (hood bumper). In years 1941-47 purchase six (6) per car. In year 1948-1949 purchase two (2) per car.
Hood to Cowl Weatherstrip
p/n: 70-1210-42
Weatherstrip, hood to cowl. Rubber. To facilitate manufacturing, some may be made in two sections.
Hood To Cowl Weatherstrip
p/n: 70-1207-42
This Hood To Cowl Weatherstrip has self-retaining stems as original. Made in two pieces to facilitate manufacturing. May need modification by customer to interlock the halves (38" long) into appearing as one continuous strip.
License Light Mounting Pad
p/n: 70-1221-17
Pad set, license light mount and lens gasket.Length: 12.625 inches.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.