Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Windshield Division Bar Gasket
p/n: 70-0059-51
Gasket, set, inner and outer, for divided windshield center post. Two (2) piece set.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Horn trumpet grommet
p/n: 70-0302-21
Grommets, horn projector. For under hood horn brackets. Two (2) per car.
Taillight Lens Gasket
p/n: 70-0652-15
Gasket, taillight lens.Length: 4.75 inches. Width: 3.25 inches.
Firewall Grommet
p/n: 70-1203-20
This Firewall Grommet is used to run various electrical and dash gauge wires through the firewall. Also see our 32-1201-20 and 32-0225-20.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Rumble Seat Lid Corner Pad
p/n: 70-0048-87
Pads, rumble seat lid corners original style, rounded triangular shape.Width: 1.25 inches.
Side Mount Cover Pad
p/n: 70-0077-37
Pads, channel type, for sidemount covers. Eight (8) piece set.Width: .25 inches. Height: .6875 inches.
2-7/16" Firewall Grommet
p/n: 70-0621-20
This Firewall Grommet is used to run the cowl vent drain hose and throttle control cable through the firewall. Designed from the original part for superior fit and seal.
2-7/16" Firewall Grommet
p/n: 70-0622-20
This Firewall Grommet is used to run the wiring harness, oil pressure tube, windshield wiper tube, capillary tube, and radio antenna wire through the firewall. Designed from the original part for superior fit and seal.
2-3/8" Firewall Grommet
p/n: 70-0350-20
This Firewall Grommet is used to run the coil wire thermometer tube through the firewall. Designed from the original part for superior fit and seal.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Rear Engine Mount
p/n: 70-0648-11
This Rear Engine Mount is used as an upper and lower support bracket at the transmission. Made from high-quality EPDM rubber for a precise, factory like fit.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Firewall Grommet
p/n: 70-0223-20
This Firewall Grommet is used on the lower end of the elbow from the firewall to the voltage regulator. Designed from the original part for superior fit and seal.
Rumble Seat Lid Corner Pad
p/n: 70-0152-87
Pads, rumble seat lid corners, original rounded triangle shape.Length: 1.5 inches. Width: .4375 inches.
Cowl Vent Hose
p/n: 60-0457-54
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Wiring Grommet
p/n: 70-0709-21
Grommet, horn wire exit from horn motor cover. Eleven thirty seconds (11/32) inch inside diameter. Two (2) per car.
Rumble Seat Step Mounting Pad
p/n: 70-0043-44
Pad, rumble seat step mounting for fender, double beaded edge per original. Width: 4.375 inches.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Convertible Top Front Bow Weatherstrip
p/n: 70-0100-64
This Convertible Top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the top of the windshield.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Trunk Hinge Mounting Pad
p/n: 70-1229-87
Mounting pad, trunk hinge. Four (4) piece set.Length: 7.625 inches.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
License plate mounting pad
p/n: 70-0124-17
Pad, rear license bracket mounting. See our other parts #70-0174-17 and #70-0348-17 sold separately.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Vent Division Bar Weatherstrip
p/n: 60-0509-56
This Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs. Sold as a pair for the drivers (LH) and passenger (RH) doors.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Brake and clutch shank seal
p/n: 70-0156-23
Grommet, brake and clutch pedal shank at toe board. Flange retained, perfect copy.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Front Bow Weatherstrip
p/n: 60-0440-64
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
Fuel Neck Grommet
p/n: 70-0091-39
Grommet, fuel filler neck. Saddle style. Three and three eighths inch (3-3/8") outside width by three and five eighths inch (3-5/8") outside length by two and one fourth inch (2-1/4") inside hole diameter by one and one fourth inch (1-1/4") height.
Accelerator Pedal Pad
p/n: 70-0275-40
Pad, accelerator pedal, full slipover type, fits over old metal after removing original rubber. Length: 8.5 inches.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Handbrake Pull Rubber Grip
p/n: 70-0385-24
Rubber grip, handbrake pull. This was an optional item alternating with a chrome handle.
Trunk Bumper
p/n: 50-0163-87
Bumper, trunk. Brass core, screw held. Two (2) per car.Length: 1.5 inches. Width: .75 inches.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Rear Stabilizer Bushing
p/n: 70-0406-33
Bushings, rear stabilizer. Comes as a four (4) piece set. Fully molded rubber.
Steering Column Collar Grommet
p/n: 70-0682-88
This Steering Column Collar Grommet is designed from the original part for superior fitment and function. The grommet fits the steering column at toe board over carpet.
Carpet Heel Plate
p/n: 70-0604-88
Heel mat, front carpet, driver's position.Length: 15.75 inches. Width: 6.25 inches.
Windshield Division Bar Gasket
p/n: 70-0159-51
This inner and outer Windshield Division Bar Gasket acts as a retainer for the outer division bar chrome molding.
Sliding Quarter Window Seal
p/n: 60-0398-78
Weatherstrip, sliding quarter window. Mounted vertically in body where leading edge of sliding window fits when closed. Right & left rubber only.
Filler Neck Extension Pad
p/n: 70-0123-41
Mounting pad, filler neck extension. Four and nine sixteenths (4-9/16) inches diameter, double bead.
Windshield Division Bar Gasket
p/n: 70-0247-51
Gasket set, windshield divider post, inner and outer. Two (2) piece set with screw holes and pilots.
Rear window division bar seal
p/n: 70-0068-82
Seal, rear window divider, inner and outer for two (2) and three (3) light rear windows, two (2) piece set for one (1) division bar.
Convertible Top Arm Pad
p/n: 70-1217-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Engine Mount
p/n: 70-0243-11
This Front Engine Mount pair is made of top quality EPDM rubber. Designed from the original part for superior fitment and function. Pads are cloth base as original.
Rumble Seat Weatherstrip
p/n: 70-0282-85
This Rumble Seat Weatherstrip is designed from the original part for superior fitment and seal. The pieces are molded as left and right for the lower corners.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Rear Door Weatherstrip Set
p/n: 90-1823-72
This Rear Door Weatherstrip Set is the primary door to body weatherstrip. Clips included for easy installation.
Side Mount Spare Wheel Grommet
p/n: 70-0099-37
Grommets, spare wheel sidemount arm.Width: 3.625 inches.
Detachable Center Post Pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Convertible Top Arm Pad
p/n: 70-1216-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Detachable Center Post Pad
p/n: 70-0279-67
Pads, for bottom of folding post or body, brass core as original, screw held.Length: 1.875 inches. Width: 1.0625 inches.
Brake Vacuum Cylinder Rod Boot
p/n: 70-0485-24
This Brake Vacuum Cylinder Rod Boot is designed from the original part for superior fitment and function. For piston type vacuum cylinders.
Carpet Heel Plate
p/n: 70-0617-88
Heel mat, front carpet insert.Length: 13.5625 inches. Width: 9.75 inches.
Front Bumper Grommet
p/n: 70-0291-28
Grommets, front bumper arm. Hollow construction for good fit. Fully molded rubber.
Hood Vent Bumper
p/n: 33-0053-42
Bumper, hood ventilator door, self retaining. Five sixteenths (5/16) inch diameter, forty eight (48) piece set.
Engine or Body Mounts
p/n: 70-0244-48
Top quality EPDM rubber Engine or Body Mount pad pair designed from the original part for superior fitment and function. Pads are cloth base as original.
Lower Suspension Arm Dust Seal Set
p/n: 70-0865-32
This four (4) piece Lower Suspension Arm Dust Seal Set is fully molded of high-quality EPDM dense rubber for durability and proper fitment. These seals are used to protect your lower suspension arm bushings from dust and debris.
Front Bumper Grommet
p/n: 70-0103-28
Grommets, front bumper. Theses are for the round, tubular bumper support.
Shock and Stabilizer Seal
p/n: 70-1184-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set. Width: 1.1875 inches.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Brake Vacuum Cylinder Rod Boot
p/n: 30-0115-24
Boot, vacuum brake cylinder main rod. Accordion type, two (2) inches diameter by six (6) inches. Top quality workmanship and material. Length: 6.0 inches.
Rear Window Division Bar Seal
p/n: 70-0475-82
Pad/Gasket set, back window division bar mounting. Set of four (4) pads, inner and outer, for two (2) dividers. Three fourths (3/4) inch wide.
Wheel cover cushion
p/n: 70-0094-38
Cushion strip for large hubcap (wheel cover). Original type, replaces that old brittle rubber to keep from losing the cover. Set of four (4) strips, approximately four (4) foot long, enough for all four (4) wheels.
Front or Rear Door Weatherstrips
p/n: 90-0128-72
This Front or Rear Door Weatherstrip set is the primary weatherstrips for the door to the body. The set contains two (2) weatherstrips for either the front or the rear doors. Purchase two (2) sets if you need to complete all four (4) doors.
Trunk Weatherstrip
p/n: 70-0083-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Door Weatherstrip
p/n: 70-0085-73
Weatherstrip, door opening, fits retainer under edge of body sill to form seal when door is closed. Six (6) foot strips.Length: 72.0 inches. Width: 1.