Handbrake Pull Rubber Grip
p/n: 70-0385-24
Rubber grip, handbrake pull. This was an optional item alternating with a chrome handle.
Trunk Bumper
p/n: 50-0163-87
Bumper, trunk. Brass core, screw held. Two (2) per car.Length: 1.5 inches. Width: .75 inches.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Rear Stabilizer Bushing
p/n: 70-0406-33
Bushings, rear stabilizer. Comes as a four (4) piece set. Fully molded rubber.
Steering Column Collar Grommet
p/n: 70-0682-88
This Steering Column Collar Grommet is designed from the original part for superior fitment and function. The grommet fits the steering column at toe board over carpet.
Carpet Heel Plate
p/n: 70-0604-88
Heel mat, front carpet, driver's position.Length: 15.75 inches. Width: 6.25 inches.
Windshield Division Bar Gasket
p/n: 70-0159-51
This inner and outer Windshield Division Bar Gasket acts as a retainer for the outer division bar chrome molding.
Sliding Quarter Window Seal
p/n: 60-0398-78
Weatherstrip, sliding quarter window. Mounted vertically in body where leading edge of sliding window fits when closed. Right & left rubber only.
Filler Neck Extension Pad
p/n: 70-0123-41
Mounting pad, filler neck extension. Four and nine sixteenths (4-9/16) inches diameter, double bead.
Windshield Division Bar Gasket
p/n: 70-0247-51
Gasket set, windshield divider post, inner and outer. Two (2) piece set with screw holes and pilots.
Rear window division bar seal
p/n: 70-0068-82
Seal, rear window divider, inner and outer for two (2) and three (3) light rear windows, two (2) piece set for one (1) division bar.
Convertible Top Arm Pad
p/n: 70-1217-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Engine Mount
p/n: 70-0243-11
This Front Engine Mount pair is made of top quality EPDM rubber. Designed from the original part for superior fitment and function. Pads are cloth base as original.
Rumble Seat Weatherstrip
p/n: 70-0282-85
This Rumble Seat Weatherstrip is designed from the original part for superior fitment and seal. The pieces are molded as left and right for the lower corners.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Rear Door Weatherstrip Set
p/n: 90-1823-72
This Rear Door Weatherstrip Set is the primary door to body weatherstrip. Clips included for easy installation.
Side Mount Spare Wheel Grommet
p/n: 70-0099-37
Grommets, spare wheel sidemount arm.Width: 3.625 inches.
Detachable Center Post Pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Convertible Top Arm Pad
p/n: 70-1216-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Detachable Center Post Pad
p/n: 70-0279-67
Pads, for bottom of folding post or body, brass core as original, screw held.Length: 1.875 inches. Width: 1.0625 inches.
Brake Vacuum Cylinder Rod Boot
p/n: 70-0485-24
This Brake Vacuum Cylinder Rod Boot is designed from the original part for superior fitment and function. For piston type vacuum cylinders.
Carpet Heel Plate
p/n: 70-0617-88
Heel mat, front carpet insert.Length: 13.5625 inches. Width: 9.75 inches.
Front Bumper Grommet
p/n: 70-0291-28
Grommets, front bumper arm. Hollow construction for good fit. Fully molded rubber.
Hood Vent Bumper
p/n: 33-0053-42
Bumper, hood ventilator door, self retaining. Five sixteenths (5/16) inch diameter, forty eight (48) piece set.
Engine or Body Mounts
p/n: 70-0244-48
Top quality EPDM rubber Engine or Body Mount pad pair designed from the original part for superior fitment and function. Pads are cloth base as original.
Lower Suspension Arm Dust Seal Set
p/n: 70-0865-32
This four (4) piece Lower Suspension Arm Dust Seal Set is fully molded of high-quality EPDM dense rubber for durability and proper fitment. These seals are used to protect your lower suspension arm bushings from dust and debris.
Front Bumper Grommet
p/n: 70-0103-28
Grommets, front bumper. Theses are for the round, tubular bumper support.
Shock and Stabilizer Seal
p/n: 70-1184-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set. Width: 1.1875 inches.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Brake Vacuum Cylinder Rod Boot
p/n: 30-0115-24
Boot, vacuum brake cylinder main rod. Accordion type, two (2) inches diameter by six (6) inches. Top quality workmanship and material. Length: 6.0 inches.
Rear Window Division Bar Seal
p/n: 70-0475-82
Pad/Gasket set, back window division bar mounting. Set of four (4) pads, inner and outer, for two (2) dividers. Three fourths (3/4) inch wide.
Wheel cover cushion
p/n: 70-0094-38
Cushion strip for large hubcap (wheel cover). Original type, replaces that old brittle rubber to keep from losing the cover. Set of four (4) strips, approximately four (4) foot long, enough for all four (4) wheels.
Front or Rear Door Weatherstrips
p/n: 90-0128-72
This Front or Rear Door Weatherstrip set is the primary weatherstrips for the door to the body. The set contains two (2) weatherstrips for either the front or the rear doors. Purchase two (2) sets if you need to complete all four (4) doors.
Trunk Weatherstrip
p/n: 70-0083-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Door Weatherstrip
p/n: 70-0085-73
Weatherstrip, door opening, fits retainer under edge of body sill to form seal when door is closed. Six (6) foot strips.Length: 72.0 inches. Width: 1.