Directional and Parking Light Lens Gaskets
p/n: 70-3095-16
This Directional Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
Front Stabilizer Bar End Link Set
p/n: 70-2110-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Headlight & Cornering Light Filler Seal Set
p/n: 70-2788-14
This six (6) piece Headlight & Cornering Light Filler Seal Set is designed from the original part for superior fitment and seal. These pieces fit behind the cornering lights.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.
Hood Bumper
p/n: 33-0861-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood Bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Hood Bumper
p/n: 70-0907-42
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Hood To Cowl Weatherstrip Bumper
p/n: 70-1251-42
This Hood To Cowl Weatherstrip Bumper is a quality reproduction of the original factory part. One fourth (1/4") of an inch high.
Hood To Cowl Weatherstrip Bumper
p/n: 70-1252-42
This Hood To Cowl Weatherstrip Bumper is a quality reproduction of the original factory part. Five sixteenths (5/16") of an inch high.
Hood to Fan Shroud Seal
p/n: 70-2789-43
This Hood To Fan Shroud Seal is designed from the original part for superior fitment and function. Attaches to bottom side of hood. This seal piece is die cut from quality masticated black rubber to authentic original dimensions.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Prop shaft support service
p/n: 70-0748-27
Bearing support bracket assembly, drive shaft center bearing. Revulcanization service only. .
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Splash Apron / A-Arm Dust Shield Set
p/n: 70-2496-45
This ten (10) piece Splash Apron / A-Arm Dust Shield set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Taillight Lens Gaskets - In Bumper
p/n: 70-3089-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the outer taillight lens & taillight housing in bumper.
Trunk Lock Emblem Gasket
p/n: 70-0875-86
Gasket, trunk lock emblem escutcheon. Steel rule die cut rubber of exact profile.Width: 1.875 inches. Height: 1.9375 inches.