Adjustable Hood Bumper
p/n: 70-2830-42
This Adjustable Hood Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires three (3) per vehicle.
Floor Pan Plug
p/n: 35-0576-45
Plug, floor pan, oval, self-retaining, fits one fourth (1/4) inch by nine sixteenths (9/16) inch hole.
Interior Dome Light Lens Gasket
p/n: 70-3102-17
This Interior Dome Light Lens Gasket is designed from the original part for superior fitment and seal. This quality reproduction gasket fits between the interior dome light lens and the dome light housing or bezel.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Rear View Mirror Mounting Pad
p/n: 70-2791-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is one (1) door mounted rear view mirror.
Hood Bumper
p/n: 70-0907-42
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Rear Stabilizer Bushing
p/n: 70-0905-33
Bushing, rear stabilizer ends. Four (4) required per car. Fully molded rubber.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Stabilizer Grommet
p/n: 70-0436-33
Grommet, front stabilizer bar link or rear shock link to axle. Fully molded rubber. Eight (8) required per car.
Shock Absorber Bushing
p/n: 70-0545-33
Bushing, rear shock absorber link, upper and lower end. Seven eighths (7/8) inch outside diameter, nine sixteenths (9/16) inch inside diameter, thirteen sixteenths (13/16) inch long. Four (4) per car.
Beltline Guide Plate - Plastic
p/n: 50-0384-62
This Beltline Guide Plate is designed from the original part for superior fitment and function. High quality plastic plate attaches to various outer beltline window scraper weatherstrips.
Front Door Lock Pillar Filler
p/n: 70-0834-79
This Front Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler seals the bottom at the front of the rear side window. Also known as a door jamb seal.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Directional & Parking Light Lens Gaskets
p/n: 70-3230-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Ferrule and Grommet Set
p/n: 70-0597-69
This Ferrule and Grommet Set for the outside door handle is cadmium plated ferrule with rubber sleeve. Two (2) piece set for one (1) door.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.
Taillight Lens Gaskets - In Fin
p/n: 70-3502-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the taillight lens & taillight housing in fin.
Back Up Light Lens Gaskets
p/n: 70-3234-17
This Back Up Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the back-up light lens and the back-up light housing or light bezel.
Parking/Backup Light Lens Gasket
p/n: 70-1272-16
Gasket, parking light lens and backup light lens. Die cut from one eighth (1/8) inch rubber.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Door Handle Gasket Set
p/n: 70-3321-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Body Mounting Pad
p/n: 70-0235-48
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped.
Glovebox Door Link Grommet
p/n: 70-0968-88
This Glovebox Door Link Grommet is designed from the original part for superior fitment and function. Grommet works to cushion the glovebox door closure.
Hood rest pad
p/n: 70-0139-42
Pad, hood rest (hood bumper). In years 1941-47 purchase six (6) per car. In year 1948-1949 purchase two (2) per car.
Hood Bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Parking Brake Pedal Pad
p/n: 70-1273-22
Pad, parking brake locking pedal.Length: 2.0625 inches. Width: 1.5 inches.
Body Mounting Pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Rear Bumper To Fender Filler
p/n: 70-2501-45
This Rear Bumper To Fender Filler pair is designed from the original part for superior fitment and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. These filler pieces fit behind each bumper end of the vehicle.
Directional & Parking Light Lens Gaskets
p/n: 70-3096-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Directional and Parking Light Lens Gaskets
p/n: 70-3115-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Taillight Lens Gaskets
p/n: 70-3235-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
A/C Grommet
p/n: 70-1040-20
This A/C Grommet is used to run the air conditioning Freon lines to the chassis. Up to six (6) required per car. Designed from original part for excellent workmanship.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
Body Mounting Pad
p/n: 70-0635-48
Cushion, body mounting pad. For underside of body bracket. Fully molded rubber with locating collar.
Stabilizer Grommet
p/n: 70-0221-33
Grommet, rear stabilizer bar (angular sway bar). Four (4) required per car. Fully molded rubber.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
Body Mounting Pad
p/n: 70-0634-48
Pad, body mounting to frame bracket. Fully molded rubber, rectangular.
Taillight Lens Gaskets - In Bumper
p/n: 70-3089-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the outer taillight lens & taillight housing in bumper.
Parking and Fog Light Lens Gaskets
p/n: 70-3159-16
This Parking and Fog Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking and Fog Light Lens and the Parking and Fog Light Housing or Bezel.
License Plate Light Gasket
p/n: 70-3334-17
This License Plate Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the License Plate Light Lens and the License Plate Light Housing or Bezel.
Cornering Light Lens Gaskets
p/n: 70-3099-17
This Cornering Light Lens Gasket pair is designed from the original part for superior fitment and seal. These quality reproduction gaskets fit between the cornering light lens and the cornering light housing or bezel.
Cornering Light Lens Gaskets
p/n: 70-3098-17
This Cornering Light Lens Gasket pair is designed from the original part for superior fitment and seal. These quality reproduction gaskets fit between the cornering light lens and the cornering light housing or bezel.
AC Condenser Mount
p/n: 70-0964-31
Mount, air conditioning condenser. Four (4) used per car.Length: 1.0 inches. Width: .75 inches.
Directional and Parking Light Lens Gaskets
p/n: 70-3095-16
This Directional Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Back Up Light Lens to Body Gaskets
p/n: 70-3119-17
This Back Up Light Lens to Body Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the back up light lens and the rear vehicle body.
1-1/4" Firewall Grommet
p/n: 70-0198-20
This Firewall Grommet is used to run the parking brake cable through the firewall. Designed from the original part for excellent workmanship.
Firewall Grommet
p/n: 70-1010-19
This Firewall Grommet is used to run the vacuum antenna line through the firewall. Designed from original part for excellent workmanship.
Cornering Light Lens Gaskets
p/n: 70-3100-17
This Cornering Light Lens Gasket pair is designed from the original part for superior fitment and seal. These quality reproduction gaskets fit between the cornering light lens and the cornering light housing or bezel.
Directional and Parking Light Lens Gaskets
p/n: 70-3116-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Fog Light Inner Gaskets
p/n: 70-3331-17
This Fog Light Inner Gasket pair is designed from the original part for superior fitment and seal. Die cut from high quality 3/16" black sponge rubber to original specifications for a factory fit.
Trunk Hinge Mounting Pads
p/n: 70-1230-87
This four (4) piece Trunk Hinge Mounting Pad is designed from the original part for superior fitment and function. The installed length is 5-1/2" inches.
Lower suspension arm dust seal
p/n: 70-0625-32
Dust seal, lower suspension arm bushing. Four (4) required per car.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Taillight Lens Gaskets
p/n: 70-3339-16
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens & taillight housing.
Hydraulic Pump Mounting Pad
p/n: 70-0986-62
Mounting bracket and pad, for hydraulic pump. Number used as required.Length: 1.75 inches. Width: .8125 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Rear Bumper End Fillers
p/n: 70-3774-30
This two (2) piece Rear Bumper End Filler pair is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Taillight & Back Up Light Lens Gasket Set
p/n: 70-3310-15
This six (6) piece Taillight Lens and Back Up Light Lens Gasket set is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight / back up light lens and housing.
Directional and Parking Light Lens Gaskets
p/n: 70-3233-16
This Directional Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Taillight Lens Gaskets - In Fin
p/n: 70-3117-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the taillight lens & taillight housing in fin.
Fuel Filler Cover Bumper
p/n: 33-0557-15
Bumper, taillight body upper half and fuel filler cover to lower half. Four (4) per set. Length: 13/16 inches. Width: 1/2 inches.
Spring shackle bushing
p/n: 70-0444-32
Bushing, rear spring shackle, upper. Four (4) required per car.
Door Weatherstrip
p/n: 70-1650-70
Seal, rear door at rear of window.Length: 1.75 inches. Width: .875 inches.
Glovebox Door Check Grommet
p/n: 70-0285-88
Grommet, glovebox door check link, for one and one eighth (1-1/8) inches slot in dash.Length: 1.4375 inches. Width: .625 inches.
Door Handle Gasket Set
p/n: 70-0771-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Handle Gasket Set
p/n: 70-0733-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Handle Gasket Set
p/n: 70-0925-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Antenna Mount Pad
p/n: 70-0392-19
Mounting pad, vacuum operated fender mounted antenna with one and one half (1-1/2) inch base.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
1-3/8" Firewall Grommet
p/n: 70-0454-20
This Firewall Grommet is used to run the handbrake cable through the firewall. Designed from the original part for superior fit and seal.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Spare Tire Bumper
p/n: 70-0125-37
Rest pad, spare wheel cover, metal core, tab held type. Sixteen (16) required per car.Width: 1.75 inches. Height: .75 inches.
Taillight Lens Gaskets
p/n: 70-3229-15
This four (4) piece Taillight Lens Gasket set is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lamp lens & taillight housing.
Glovebox Door Check Grommet
p/n: 70-0467-88
Grommet, glovebox door check link, for one (1) inch slot in dash.
Upper Radiator Filler
p/n: 70-2784-45
This single piece Upper Radiator Filler is designed from the original part for superior fitment and function. This upper radiator to core support filler piece is die cut from quality masticated rubber to authentic original dimensions.
Hood Rest Pad
p/n: 70-0150-42
Pad, hood rest, molded to brass core, screw mounted.Width: 1.75 inches.
Directional & Parking Light Lens Gaskets
p/n: 70-3092-16
This Directional Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the signal / parking light lens and the signal / parking light housing or bezel.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Phototube Mounting Pad
p/n: 70-0721-17
Pad, phototube mounting on instrument panel. Automatic headlight beam control.Length: 2.3125 inches. Width: 1.6785 inches.
Taillight Lens Gaskets - In Bumper Ends
p/n: 70-4923-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens and taillight housing bezel in each bumper end.
Spare Tire Bumper
p/n: 70-0126-37
Rest pad, spare wheel cover, metal core, screw held type. Eight (8) required per car.Width: 1.75 inches. Height: 1.4375 inches.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Directional Signal or Fog Light Lens Gaskets
p/n: 70-3093-17
This Directional Turn Signal or Fog Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Directional Signal / Fog Light Lens and the Directional Signal / Fog Light Housing or Bezel.
Firewall Grommet
p/n: 70-1089-20
This Firewall Grommet is used to run the heater hose through the firewall. Designed from the original part for superior fit and seal.
Door Check Link Rod End Stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.