Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Rear Bumper Gravel Shield
p/n: 60-0173-30
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. Fully molded rubber with all original features.
Fender Skirt Edge Weatherstrip
p/n: 60-0201-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrips fits between the removable fender skirt and the rear fender quarter panel.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Steering Column Floorplate
p/n: 60-0403-24
This Steering Column Floorplate is used as the steering gear and clutch pedal push rod dash seal. Fully molded with original style pattern. Does not have metal backing.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Rear Bumper Gravel Shield
p/n: 60-0213-30
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. This seal is the exact profile as original.
Accelerator Pedal
p/n: 60-0240-40
This reproduction Accelerator Pedal replaces worn or broken originals. Manufactured in quality black rubber. Steel core with hinge. Length: 8-15/16 inches.
Trunk Weatherstrip
p/n: 70-1122-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid. The seal glues directly to the trunk lid.
Window Division Bar Filler
p/n: 70-2661-62
This Window Division Bar Filler is sold as a four (4) piece set for the upper and lower. This filler set fits into inside garnish molding between rear seat side window and rear side window.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Roof Rail Filler
p/n: 60-0429-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes. High-quality EPDM rubber a solid brass core.
Roof Rail Filler
p/n: 70-3644-73
Filler, side roof rail. Front corner, just in front of flipper seal. Right and left, solid brass core, molded screw holes.
Hood To Cowl Weatherstrip
p/n: 60-0153-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact copy reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Door Flipper Stops
p/n: 70-2853-62
This Door Flipper Stop pair is designed from the original part for superior fitment and function. These rear flipper stops mount inside the flipper opening at the very rear of the door flipper.
Parking Light Lens Gasket
p/n: 60-0672-17
This Parking Light Gens Gasket pair is die cut from one-eighth (1/8) inch sponge rubber.
Hood To Cowl Weatherstrip
p/n: 70-1698-43
This Hood To Cowl Weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. A reproduction designed from original part so it fits correctly.
Taillight Gasket
p/n: 60-0691-15
This Taillight Gasket is made of fully molded soft-dense rubber compound to ensure proper installation and performance. Designed from the original part for the correct profile. Two (2) strips cut thirty-six (36) inches long.
Exhaust System Hanger
p/n: 60-0307-13
This Exhaust System Hanger is used for the muffler-to-tailpipe support (insulator) with reinforced webbing. Fully molded from top-quality EPDM dense rubber to ensure durability. One (1) required per car.
Firewall Grommet
p/n: 60-0565-20
This Firewall Grommet is used to run the top hydraulic lines, wiring harness, and speedometer cable through the firewall. Designed from the original part for superior fit and seal.
Steering Column Connecting Rod Seal
p/n: 60-0400-36
Steering column steering connecting rod seal. Power steering models require one (1) per car. Non-power steering models require two (2) per car.
Roof Rail Filler
p/n: 70-1763-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes.
Brake and Clutch Pedal Bumpers
p/n: 60-0104-24
Bumpers, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with part 60-0579-24.
Body to Frame Mounting Pad
p/n: 60-0188-48
This Body to Frame Mounting Pad with locating collar functions as a body to frame isolator mounting pad. Molded from a top-quality EPDM rubber with a metal core, locating collar, and metal bolt. Two (2) required per vehicle.
Steering Column Seal
p/n: 60-0518-36
Seal, steering column and shift column toe pan. Five eighths (5/8) inch thick sponge rubber.Width: 4.875 inches. Height: .625 inches.
Lock Pillar Water Deflector
p/n: 70-3635-62
Door panel water deflector, at lock. Fully molded for both left and right hand sides.
Brake and Clutch Pedal Pads
p/n: 60-0300-22
Pad, brake and clutch pedal.Length: 3.0 inches. Width: 2.5625 inches.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Body Mounting Pad
p/n: 60-0119-48
This Body Mounting Pad with locating collar functions as a body to frame isolator mounting pad. Molded from a top-quality EPDM rubber with metal core and metal bolt liner.
Hood To Cowl Weatherstrip
p/n: 60-0346-42
This Hood To Cowl Weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. The strip is designed from the original part for superior fitment and complete coverage.
Antenna Mount Pad
p/n: 60-0338-21
This Antenna Mount Pad is a high-quality reproduction of the original factory part. This mount pad installs between the antenna mounting base and fender to protect the surface.
Hood Rest Pad Set
p/n: 60-0351-42
This six (6) piece Hood Rest Pad Set is self-retained in the slot on the fender ledge. Designed from the original parts for superior fitment and function.
Taillight To Body Gaskets
p/n: 70-3766-15
This Taillight To Body Gasket pair is designed from the original part for superior fitment and sealing. Installs under the taillight assembly. Die cut masticated rubber to authentic original dimensions.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Cowl Drain Gutter Hose Grommet
p/n: 33-0329-54
This Cowl Drain Gutter Hose Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
1-3/16" Standard Grommet
p/n: 32-0328-54
This Standard Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Window Regulator | Accelerator Rod Seal
p/n: 60-0652-70
This Window Regular | Accelerator Rod Seal is used as a front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Exhaust Tailpipe Hanger Strap
p/n: 60-0308-13
This Exhaust Tailpipe Hanger Strap is made from high-quality rubber for a precise, factory like fit for your classic vehicle. Muffler/tailpipe system, reproduction strap type is manufactured to OEM specifications.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Hood To Fender Bumper
p/n: 60-0318-42
This Hood To Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle, order as needed.