Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Quarter Window Vertical Leading Edge
p/n: 60-0599-80
This quarter and side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. A reproduction manufactured to OEM specifications to install for an authentic fit and finish.
Rear Lower Engine Mount
p/n: 60-0459-11
This Rear Lower Engine Mount is designed from original part for correct fitment and function. The mount is made from a dense rubber for durability and proper engine vibration isolation.
Rear Upper Engine Mount
p/n: 60-0463-11
This Rear Upper Engine Mount is designed from original part for correct fitment and function. Made of a high-quality EPDM dense rubber for durability and proper engine vibration isolation.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Shock Absorber Bushing
p/n: 70-0547-32
This Shock Absorber Bushing is manufactured with high-quality EPDM rubber to OEM specifications. The bushing is the double cone style. Designed from original part to ensure proper fit.
Shock Absorber Grommet
p/n: 60-0235-33
This Shock Absorber Grommet is fully molded and designed from the original part for superior fitment and durability. The grommet the plain cylinder type with flat ends for shock absorber mounting.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Side window leading edge
p/n: 60-0656-80
Side window vertical leading edge weatherstrip. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Molded authentic rubber construction with metal core, this part does not include the chrome piece
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Tailgate Latch Striker Bumper
p/n: 70-1911-87
This Tailgate Latch Striker Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the station wagon tailgate to cushion its closure. Usually requires two (2) bumpers each per vehicle.
Transmission Mount Service
p/n: 60-0465-25
Transmission mount. One (1) per car. Revulcanization service only.Length: 5.75 inches.
Transmission Mount Service
p/n: 60-0464-25
Transmission mounts. Revulcanization service only.Center of hole to center of hole measures 4.375 inches apart.Length: 4.375 inches.
Vent division bar weatherstrip
p/n: 60-0650-56
Front vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. See Front door vent weatherstrip for main rubber seal.
Vent division bar weatherstrip
p/n: 60-0587-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Window Division Post Weatherstrips
p/n: 70-1936-56
This front Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. These pieces mount on the vertical division bar / post with tabs and seal as the vent glass closes against them.
Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
Window Felt Beltline Weatherstrips
p/n: 80-0362-57
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This eight (8) piece set includes inner and outer window felt beltline weatherstrips for each side window and quarter window.
Window Felt Beltline Weatherstrips
p/n: 80-0360-57
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This eight (8) piece set includes inner and outer window felt beltline weatherstrips for each door side window.
Window Felt Beltline Weatherstrips
p/n: 80-0355-57
Original equipment style side window horizontal seal kit (also known as beltline weatherstrip). Four (4) piece kit includes inner and outer felt beltline weatherstrips for each door side window.
Window Regulator | Accelerator Rod Seal
p/n: 60-0652-70
This Window Regular | Accelerator Rod Seal is used as a front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
Wiper Transmission Gasket
p/n: 60-0593-53
Wiper Transmission Gasket - This is the seal for the wiper motor crank. For two (2) speed wiper motors only. These parts are made of the highest quality and authenticity. Replaces # 4906021.