Window Felt and Run Channel Set
p/n: 90-0140-58
This eight (8) piece Window Felt and Run Channel set includes the inner and outer window felts, upper rigid run channels, and flexible run channels needed to complete two doors. The set can be used for front or rear doors in models with vent windows in the door.
Front Door Vent Window Set
p/n: 90-0452-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0022-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Engine Mount Service – Revulcanization Only
p/n: 60-0422-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Transmission Mount - Revulcanization Service Only
p/n: 60-0627-25
This Transmission Mount - Revulcanization Service Only is designed to restore your transmission mount to a like new original condition. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 60-0390-11
This Revulcanization Service Only is designed to restore your Side Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Side Support Mounts
p/n: 60-0305-11
This Engine Side Support Mount pair is designed from the original part for superior fitment and function. A round type support cushion at the side frame bracket to clutch housing.
Ferrule Installing Tool
p/n: 70-0662-69
This is an installation tool for door and trunk handle ferrules. For cars and trucks using door and trunk handle ferrules such as our 70-0111-69.
Windshield Gasket
p/n: 60-0366-50
This Windshield Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Engine Mount Service – Revulcanization Only
p/n: 60-0502-11
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Transmission Mounting Pad
p/n: 60-0303-25
Insulator replacement set. 2-piece unit of special soft rubber to be used with original steel channel and plate.
Rear Spare Wheel Carrier Pad
p/n: 60-0164-37
Pad, rear mounted spare wheel support. Seven (7) inch by seven (7) inch, three (3) hole pattern, brass core as original.Width: 7.0 inches. Height: 7.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft.
p/n: 70-1098-44
Fender Welting is typically used to attach four (4) fenders to body. A superior quality, proper construction of reinforced black vinyl over vinyl core. Measures one and three eighths (1-3/8) inch wide. Fifty (50') foot roll of one-fourth (1/4) inch bead.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Front Spring Bumper
p/n: 60-0021-35
Rebound bumper, front spring and rear spring for beam axle cars, steel ring reinforced as original.Height: 2.4375 inches.
Hood Rear Corner Pads
p/n: 60-0053-42
Left and Right Front Hood Corner Pad pair designed from the original part for superior fitment, finish and function. Has metal core as original, with metal tabs for securing pad to hood.
Side mount spare wheel grommet
p/n: 60-0331-37
Grommet, sidemount wheel carrier-through-fender, right and left.
Hood Front Corner Pads
p/n: 60-0052-42
Left and Right Front Hood Corner Pad pair designed from the original part for superior fitment, finish and function. Has metal core as original, with metal tabs for securing pad to hood.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Brake Cable Boot
p/n: 60-0155-24
Boot, rear, brake cable end at brake backing plate. Three and one half (3-1/2) inches long.Length: 3.50 inches.
Vent division bar weatherstrip
p/n: 60-0689-55
Front door vent window divsion bar seal. Proper cross section rubber seal bonded to metal core with authentic style mounting tabs.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft.
p/n: 70-1097-44
Fender Welting is typically used to attach two (2) fenders to body. A superior quality, proper construction of reinforced black vinyl over vinyl core. Measures one and three eighths (1-3/8) inch wide. Twenty-five (25') foot roll of one-fourth (1/4") inch bead.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0043-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber. Excellent detail with bowtie emblem like original.
Accelerator Pedal Pad
p/n: 60-0430-40
Cover, accelerator pedal. Exact pattern of original. Slipover type. Use your old steel core. Length: 7.875 inches.
Fender Welting with 3/16 Bead - 25ft.
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a twenty-five (25') foot roll.
Accelerator Rod Seal
p/n: 60-0086-40
Grommet, accelerator rod through toe board. Brass core as original.
Fuel Neck Grommet
p/n: 60-0405-41
Grommet, fuel filler neck. Oblong, fully molded rubber. Three and eleven sixteenths inch (3-11/16") outside width by four and one fourth (4-1/4") outside length. Two and one fourth inch (2-1/4") inside hole diameter by one half inch (1/2") height.
Taillight Mounting Pad
p/n: 60-0075-15
Pad, taillight and license bracket mounting. Two and five eighths (2-5/8) inch by four and one half (4-1/2) inch. Length: 4.5 inches. Width: 2.625 inches.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Headlight Grommet
p/n: 60-0154-14
Grommet, headlight and horn wire conduit through radiator shell. Two (2) holes for two (2) separate conduits.Height: .21875 inches.
Firewall Grommet
p/n: 60-0010-45
This Firewall Grommet is the oblong four (4) hole style. The grommet fits the steel retainer for the throttle and choke cables, and the oil and temperature lines.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Steering Column Cushion - Brown
p/n: 60-0012-89
This Steering Column Cushion grommet is designed from the original part for an authentic fit, finish, and appearance. For the steering column to cowl U-bolt clamp. Brown rubber. For Black see 60-0012-36
Steering Column Cushion - Black
p/n: 60-0012-36
This Steering Column Cushion grommet is designed from the original part for an authentic fit, finish, and appearance. For the steering column to cowl U-bolt clamp. Black rubber. For Brown see 60-0012-89.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Side Window Lower Bump Stop
p/n: 70-0110-62
This Side Window Lower Bump Stop is designed from the original part for an authentic fit, finish, and function. Requires two (2) stops per window.
Handbrake Lever Anti-Rattle
p/n: 60-0531-24
Spacer, anti-rattle, handbrake lever sector rod, between release rod and handbrake lever.Width: .6875 inches. Height: .6875 inches.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.
Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Door Handle Grommet
p/n: 70-0009-69
Grommet, for outside door handle ferrule (our #70-0111-69, ordered separately). Molded rubber with cloth covering per original.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Door Check Link Rod End Stop
p/n: 70-0325-70
A quality Door Check Link Rod End Stop for rod type door check mechanism. One (1") inch diameter by three-eighths (3/8") inch thick with five-sixteenths (5/16") inch hole.
11/16" Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel. Available by the foot.
Brake Cable Shielding Cover - 2 Inch
p/n: 70-1701-24
This two (2) inch long Brake Cable Shielding Cover is designed install for an authentic fit, finish and function. Fits all models with seven sixteenths (7/16) inch outside diameter cable.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
9/16" Window Weatherstrip
p/n: 70-1195-52
This Window Weatherstrip is for models with lip for attaching bead molding. Available by the foot.
Spring Shackle Pin Neoprene Washer
p/n: 70-1125-33
This Spring Shackle Pin Neoprene Washer is designed from the original part for superior fitment and function. Rubber washer fits the front and or rear spring shackle pin. Constructed of neoprene rubber.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.