Trunk Weatherstrip
p/n: 70-0798-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Taillight Mounting Pad
p/n: 60-0545-15
Pad, bracket mounting to body for tail and license plate light. Length: 3.3125 inches. Width: 2.5625 inches.
Taillight Mounting Pad
p/n: 60-0075-15
Pad, taillight and license bracket mounting. Two and five eighths (2-5/8) inch by four and one half (4-1/2) inch. Length: 4.5 inches. Width: 2.625 inches.
Trunk Hinge Mounting Pad
p/n: 60-0139-87
Pad, trunk hinge mounting, upper and lower. Four (4) piece set.
Starter Pedal Bellows
p/n: 60-0487-21
Bellows, starter pedal shaft-to-floorboard. One and three fourths (1-3/4) inch by two and one fourth (2-1/4) inch.Length: 2.25 inches. Width: 1.75 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Battery Carrier Edge Liner
p/n: 60-0112-21
Edge liner, battery carrier cover.Length: 42.0 inches. Width: .25 inches. Height: .6875 inches.
Taillight Mounting Pad
p/n: 60-0172-15
Pad, taillight bracket mounting. Five and one half (5-1/2) inches long. Compare with our #60-0116-15. Length: 5.50 inches.
Horn Button Contact Ring
p/n: 60-0157-21
Ring, horn button contact. Accessory banjo steering wheel. Four and one eighth (4-1/8) inch outside diameter.
Horn Button Contact Cushion
p/n: 60-0192-21
Cushion, standard steering wheel horn button contact. Two and one half (2-1/2) inch diameter.
Fuel Filler Neck Grommet
p/n: 60-0022-41
This Fuel Filler Neck Grommet is fully molded rubber and slightly angled. Three and eleven sixteenths inch (3-11/16") outside diameter by two and three sixteenths inch (2-3/16") top hole diameter by two and five eighths inch (2-5/8") bottom hole diameter.
Brake and Clutch Pedal Bumper
p/n: 60-0024-24
Bumpers, brake and clutch pedal shank to floorboard. Rides pedal shank under floorboard.
Fuel Neck Grommet
p/n: 60-0405-41
Grommet, fuel filler neck. Oblong, fully molded rubber. Three and eleven sixteenths inch (3-11/16") outside width by four and one fourth (4-1/4") outside length. Two and one fourth inch (2-1/4") inside hole diameter by one half inch (1/2") height.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Rumble Seat Lid Corner Pad
p/n: 70-0152-87
Pads, rumble seat lid corners, original rounded triangle shape.Length: 1.5 inches. Width: .4375 inches.
Accelerator Rod Seal
p/n: 60-0086-40
Grommet, accelerator rod through toe board. Brass core as original.
Fuel Neck Grommet
p/n: 60-0040-41
Grommet, fuel filler neck. Fully molded rubber, slightly angled with retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Front Bumper Seal
p/n: 70-1103-28
Seals, front bumper. Fully molded rubber, U-shaped. Three and one half inches (3-1/2") long by three and one half inches (3-1/2") wide by thirteen sixteenths inch (13/16") height. For the grommets see our #70-1104-28, sold separately.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Accelerator Pedal Pad
p/n: 60-0430-40
Cover, accelerator pedal. Exact pattern of original. Slipover type. Use your old steel core. Length: 7.875 inches.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0043-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber. Excellent detail with bowtie emblem like original.
Headlight Mounting Pad
p/n: 60-0115-14
Pad, headlight support bracket. Two and one half (2-1/2) inch by six and one fourth (6-1/4) inch.Length: 6.25 inches. Width: 2.5 inches.
Trunk Hinge Mounting Pad
p/n: 60-0604-87
Pads, trunk hinge. 6 (six) piece set sold in complete sets only.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fuel Neck Grommet
p/n: 60-0181-41
Grommet, fuel filler neck. Fully molded rubber, slightly angled with retaining flange. Three and seven sixteenths inch (3-7/16") outside width by three and five eights inch (3-5/8") outside length.
Accelerator Pedal Pad
p/n: 60-0097-40
Pad, accelerator pedal. Slip-over type for original core. Length: 9.125 inches.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Hood To Radiator Weatherstrip
p/n: 60-0111-42
This Hood To Radiator Weatherstrip is molded with four (4) self retaining carrots for easy installation. Sold as a pair for the left and right sides.
Fuel Neck Grommet
p/n: 60-0543-41
Seal, gas tank filler tube through floor pan, to inside of body. Made of soft flexible durometer rubber. Four and seven sixteenths inch (4-7/16") outside width by five and five eights inch (5-5/8") outside length.
Vent division bar weatherstrip
p/n: 60-0689-55
Front door vent window divsion bar seal. Proper cross section rubber seal bonded to metal core with authentic style mounting tabs.
Brake Cable Boot
p/n: 60-0155-24
Boot, rear, brake cable end at brake backing plate. Three and one half (3-1/2) inches long.Length: 3.50 inches.
Vent Window Division Post Weatherstrips
p/n: 60-0596-56
This Front Window Vent Division Post Weatherstrip pair is fully molded with metal core and attaching tabs.
Cowl Vent Weatherstrip
p/n: 70-0224-54
Weatherstrip, cowl vent. Original solid rubber configuration, not a sponge substitute. A top quality part for your classic vehicle restoration.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Headlight Mounting Pad
p/n: 60-0211-14
Mounting pad, headlight bracket to fender.Length: 4.8125 inches.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0125-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber with Chevy bowtie in tread.
Fuel tank support pad
p/n: 60-0026-41
Pad, fuel tank support and floorboard seal. Sponge rubber ring. Two (2) per car.