Firewall Grommet
p/n: 60-0010-45
This Firewall Grommet is the oblong four (4) hole style. The grommet fits the steel retainer for the throttle and choke cables, and the oil and temperature lines.
Firewall Grommet
p/n: 60-0013-20
This Firewall Grommet is used to run the wiring harness and speedometer cable through the toe board. Designed from the original part for superior fit and seal.
Steering column seal
p/n: 60-0478-36
Seal, steering column at toe board, for steering column housing and shifter control shaft jacket. Top quality sponge rubber, accurately cut.
Door Check Link Rod End Stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Trunk Handle Grommet
p/n: 50-0183-87
Grommet, trunk handle bezel-thru-trunk lid. Special size, one (1) inch inside diameter.Buick 1937 Grommet, trunk handle bezel-thru-trunk lid.
Taillight Mounting Pad
p/n: 60-0472-15
Pad, taillight bracket mounting. Two and three sixteenths (2-3/16) inch by three and three fourths (3-3/4) inch inside of bead.
Brake and Clutch Pedal Bumpers
p/n: 60-0104-24
Bumpers, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with part 60-0579-24.
Taillight Mounting Pad
p/n: 60-0495-15
Pad, taillight bracket to fender. Can be used for right or left hand. Two and one half (2-1/2) inch by three and five eighths (3-5/8) inch overall.
License Light Mounting Pad and Grommet Set
p/n: 60-0337-17
This License Light Mounting Pad and Grommet Set is designed from the original part for superior fitment and function. Mounting Pad for the license light to trunk lid. The Grommet is for the license bracket spacer post.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Choke Cable Support Grommet
p/n: 60-0373-13
Grommet, choke cable support-at-ignition cable.Width: 1.25 inches.
Taillight Lens Gasket
p/n: 60-0100-15
Gasket, taillight lens.Length: 5.125 inches. Width: 1.875 inches.
Horn projector grommet
p/n: 60-0161-21
Grommet, horn trumpet through horn mounting bracket. For Deluxe country horn.
Hood to Cowl Weatherstrip
p/n: 60-0138-42
This Hood To Cowl Weatherstrip pair installs at the rear of the engine bay to seal between the hood and vehicle body cowl. Sold as a pair for left and right side.
Taillight Lens Gasket
p/n: 60-0147-15
Gasket, taillight lens. Two and three fourths (2-3/4) inch diameter.
Trunk Hinge Mounting Pad
p/n: 60-0139-87
Pad, trunk hinge mounting, upper and lower. Four (4) piece set.
Starter Pedal Bellows
p/n: 60-0487-21
Bellows, starter pedal shaft-to-floorboard. One and three fourths (1-3/4) inch by two and one fourth (2-1/4) inch.Length: 2.25 inches. Width: 1.75 inches.
Trunk Hinge Mounting Pad
p/n: 70-1231-87
Mounting pads, trunk hinge. Four (4) piece set.Length: 8.8125 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
Center Division Bar Chrome Molding Retainer
p/n: 70-0373-51
Center Division Bar Chrome Molding Retainer for outside windshield center post stainless molding. Use with original stainless molding and clips. Length: 15-1/2 inches. Width: 1-1/4 inches.
Battery Carrier Edge Liner
p/n: 60-0112-21
Edge liner, battery carrier cover.Length: 42.0 inches. Width: .25 inches. Height: .6875 inches.