Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Steering Gear Pitman Arm Bushing
p/n: 60-0105-36
This Steering Gear Pitman Arm Bushing is designed from the original part for superior fitment and function. Fully molded with steel core.
Steering Column Gearshift Vacuum Boot
p/n: 60-0555-24
This Steering Column Vacuum Cylinder Boot is designed from the original part for superior fitment, finish and function. An excellent duplicate of original.
Steering knuckle support seal
p/n: 60-0089-32
Seal, steering knuckle support, upper. Four (4) per car.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Body Mounting Pad
p/n: 60-0027-48
Pad, side body mounting. Fully molded rubber, rectangular. Two and seven-sixteenths inch (2-7/16") outside length by one and five-eights inch (1-5/8") outside width by one-fourth inch (1/4") height.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Starter Pedal Bellows
p/n: 60-0210-21
Bellows, starter pedal shaft to floorboard. Three eighths (3/8) inch top hole with three (3) inch height.Width: 2.875 inches. Height: 3.0 inches.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
1-11/16" Firewall Grommet
p/n: 60-0057-21
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from original parts for excellent workmanship.
1-11/16" Firewall Grommet
p/n: 32-0196-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
Exhaust Support Grommet
p/n: 60-0031-13
This Exhaust Support Grommet is designed from the original part for superior fitment and usage. The OEM direct fit application is as a rear and middle muffler exhaust support hanger.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Steering Column Seal
p/n: 60-0419-36
Seal, steering column toe pan. One (1) required per car. Top quality sponge rubber, five eighths (5/8) inch thick.Width: 3.50 inches. Height: .625 inches.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Brake and Clutch Pedal Bumpers
p/n: 60-0104-24
Bumpers, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with part 60-0579-24.
License Light Mounting Pad and Grommet Set
p/n: 60-0337-17
This License Light Mounting Pad and Grommet Set is designed from the original part for superior fitment and function. Mounting Pad for the license light to trunk lid. The Grommet is for the license bracket spacer post.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Hood to Cowl Weatherstrip
p/n: 60-0056-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Cowl Vent Hose
p/n: 60-0457-54
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
Fuel Neck Grommet
p/n: 60-0040-41
Grommet, fuel filler neck. Fully molded rubber, slightly angled with retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Trunk Hinge Mounting Pad
p/n: 50-0106-87
Mounting pads, trunk hinge, four (4) piece set. Models with outside hinges.Length: 8.25 inches.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Accelerator Pedal Pad
p/n: 60-0448-40
Pad, accelerator pedal, slip-over type. Attaches to your original pedal core, does not include attachment or linkage sockets.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Windshield Division Bar Gasket
p/n: 70-0372-51
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part is properly sized with "H" section. Part requires fitting to top and bottom, as it is not drilled.