Brake and clutch shank seal
p/n: 60-0019-24
Seal, brake and clutch pedal shank to floorboard. Single bellows rubber cup, seals air drafts around pedals.
Accelerator Rod Seal
p/n: 60-0086-40
Grommet, accelerator rod through toe board. Brass core as original.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Fuel Filler Neck Grommet
p/n: 60-0022-41
This Fuel Filler Neck Grommet is fully molded rubber and slightly angled. Three and eleven sixteenths inch (3-11/16") outside diameter by two and three sixteenths inch (2-3/16") top hole diameter by two and five eighths inch (2-5/8") bottom hole diameter.
Taillight Mounting Pad
p/n: 60-0172-15
Pad, taillight bracket mounting. Five and one half (5-1/2) inches long. Compare with our #60-0116-15. Length: 5.50 inches.
Headlight Mounting Pad
p/n: 60-0163-14
Pad, headlight bracket mounting right and left. One and seven eighths (1-7/8) inch by two and seven eighths (2-7/8) inch overall.Length: 2.875 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Starter Pedal Bellows
p/n: 60-0487-21
Bellows, starter pedal shaft-to-floorboard. One and three fourths (1-3/4) inch by two and one fourth (2-1/4) inch.Length: 2.25 inches. Width: 1.75 inches.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Trunk Weatherstrip
p/n: 70-0798-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Taillight Mounting Pad
p/n: 60-0364-15
Pad, taillight mounting to rear fender. Length: 1.0625 inches.
Windshield Division Bar Gasket
p/n: 70-0059-51
Gasket, set, inner and outer, for divided windshield center post. Two (2) piece set.
Taillight Mounting Pad
p/n: 60-0116-15
Pad, taillight bracket to fender. Four (4) inches long. Compare with our #60-0172-15 and #60-0545-15. Length: 4.0 inches.
Firewall Grommet
p/n: 60-0010-45
This Firewall Grommet is the oblong four (4) hole style. The grommet fits the steel retainer for the throttle and choke cables, and the oil and temperature lines.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Exhaust Support Grommet
p/n: 60-0031-13
This Exhaust Support Grommet is designed from the original part for superior fitment and usage. The OEM direct fit application is as a rear and middle muffler exhaust support hanger.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.