Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Door Weatherstrip
p/n: 60-0114-73
Weatherstrip, door bottom, sponge constant section, solid skin surface, superior quality. Sold in six (6) foot strips only.Length: 72.0 inches.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Fuel Filler Neck Grommet
p/n: 60-0040-41
This Fuel Filler Neck Grommet is a fully molded rubber, grommet slightly angled with a retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Cowl Vent Hose
p/n: 60-0457-54
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
License Light Mounting Pad
p/n: 60-0074-17
Mounting pad, license light. Three and one eighth (3-1/8) inch by eight and seven eighths (8-7/8) inch. Fully detailed.Length: 8.875 inches.
Backup Light Mounting Pad
p/n: 60-0072-17
Mounting pads, back up lights, elliptic, sharp beaded edge. One and five sixteenths (1-5/16) inch by two and seven eighths (2-7/8) inch.Length: 2.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Hood to Cowl Weatherstrip
p/n: 60-0090-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This pair comes with pre-drilled holes for easy installation.
Center Division Bar Chrome Molding Retainer
p/n: 70-0373-51
Center Division Bar Chrome Molding Retainer for outside windshield center post stainless molding. Use with original stainless molding and clips. Length: 15-1/2 inches. Width: 1-1/4 inches.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
Parking Light Lens Gasket
p/n: 60-0206-17
Gasket, parking light lens. Top quality, one eighth (1/8) inch sponge.Length: 6.3125 inches. Width: 2.0 inches.
Taillight Lens Gasket
p/n: 60-0100-15
Gasket, taillight lens.Length: 5.125 inches. Width: 1.875 inches.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Clutch and Brake Pedal Bumpers
p/n: 60-0104-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment and function. Pedal shank rides under floorboard. One and one-eighth (1-1/8") inch clearance for pedal shaft.
Door Check Link Rod End Stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Steering column seal
p/n: 60-0478-36
Seal, steering column at toe board, for steering column housing and shifter control shaft jacket. Top quality sponge rubber, accurately cut.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Trunk handle bezel and grommet
p/n: 60-0526-87
Bezel and grommet, trunk handle and license light body.
Exhaust Support Grommet
p/n: 60-0031-13
This Exhaust Support Grommet is designed from the original part for superior fitment and usage. The OEM direct fit application is as a rear and middle muffler exhaust support hanger.
1-11/16" Firewall Grommet
p/n: 60-0057-21
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from original parts for excellent workmanship.
Window Stop Stem Bumpers
p/n: 33-0675-62
This Window Stop Stem Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Cushion window stop pair for the lower front and or rear doors rear side and quarter windows as needed.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Ferrule and Grommet Set
p/n: 70-0597-69
This Ferrule and Grommet Set for the outside door handle is cadmium plated ferrule with rubber sleeve. Two (2) piece set for one (1) door.
Starter Pedal Bellows
p/n: 60-0210-21
This Starter Pedal Bellows is designed from the original part for an authentic fit, finish, and appearance. This bellows fits to the starter pedal shaft to floorboard.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Wiper Transmission To Cowl Gaskets
p/n: 60-0101-53
This Wiper Transmission To Cowl Gasket pair is designed from the original part for superior fitment and seal. Gaskets are precision die cut from quality dense rubber material.
Rear Shock Absorber Link Bushing
p/n: 60-0521-33
This Rear Shock Absorber Link Pin Bushing is designed from the original part for superior fitment and function. Four (4) per car for double action shocks.
Steering knuckle support seal
p/n: 60-0089-32
Seal, steering knuckle support, upper. Four (4) per car.
Door Lock Mounting Pad
p/n: 27-0020-69
Mounting pad, door lock cylinder, right and left.Length: 1.6875 inches.
Steering Column Gearshift Vacuum Boot
p/n: 60-0555-24
This Steering Column Vacuum Cylinder Boot is designed from the original part for superior fitment, finish and function. An excellent duplicate of original.
Steering Gear Pitman Arm Bushing
p/n: 60-0105-36
This Steering Gear Pitman Arm Bushing is designed from the original part for superior fitment and function. Fully molded with steel core.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
15/16" Trunk Weatherstrip
p/n: 70-0490-85
This Trunk Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Wiper control grommet
p/n: 60-0197-53
Grommet, wiper control connection link. Replaces #4161287. 11/32" I.D. X 19/32" O.D.
15/16" Trunk Weatherstrip
p/n: 70-0412-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
13/16" Trunk Weatherstrip
p/n: 50-0161-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Door Weatherstrip
p/n: 40-0168-73
This Door Weatherstrip is generally used as a hinge post on door or body opening, in area around hinges where irregular cross section is required. Available by the foot.
Lower Control Arm Bushing Seal
p/n: 60-0095-32
This Lower Control Arm Bushing Seal is designed from the original part for superior fitment and seal. Installs at the lower control arm pivot bolt bushing. Four (4) per car.