Rear Door Vent Window Kit
p/n: 90-0463-90
This rear door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Windshield Gasket
p/n: 70-3520-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners. Designed from original part for a precise, factory fit.
Rear Door Vent Window Weatherstrips
p/n: 70-3643-74
These rear door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Door Vent Window Weatherstrips
p/n: 70-2862-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-1691-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The self-adhesive weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Trunk Weatherstrip
p/n: 70-1691-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Front Suspension Bumpers
p/n: 40-0251-32
This Front Suspension Bumper pair for the upper arm is made from high-quality EPDM dense rubber for a precise, factory like fit. Two (2) required per car.
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Beltline Weatherstrip
p/n: 40-0540-57
This six (6) foot Beltline Weatherstrip installs on the left and right doors to wipe the side windows when the glass is lowered. Flexible, pile lined, rubber covered, with black bead. Available in 6ft. lengths.
Brake and Clutch Pedal Pad
p/n: 40-0287-22
Pads, brake and clutch pedal. Length: 3.625 inches. Width: 2.0 inches.
Vent Window Division Bar Weatherstrip
p/n: 70-1432-56
This Front Vent Window Division Bar Weatherstrip is designed from the original part for superior fitment and seal. A single 32" inch (approximate) length of original cross-section extruded rubber.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Body Mount Isolator Pad
p/n: 40-0234-48
This Body Mount Isolator Pad functions as a body to frame isolator mounting pad. Made of high quality EPDM rubber with a high level of fit and finish.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Body Mounting Pad
p/n: 40-0324-48
Cushion, used as either a body mounting pad or for all body bolt nuts, below brackets. Fully molded rubber. Two inch (2") outside diameter by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Hood to Cowl Weatherstrip
p/n: 40-0475-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip can also be used as a radiator seal. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
3/4" Trunk Weatherstrip
p/n: 30-0356-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Hood Bumper
p/n: 70-1607-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to support / cushion the hood closure.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.