Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Accelerator Rod Seal
p/n: 40-0205-88
This Accelerator Rod Seal is used as an accelerator rod through the toeboard. Molded from a high-quality EPDM dense rubber.
Side Mount Grommet
p/n: 40-0140-37
Grommet, sidemount carrier brace to fender. One and five sixteenths (1-15/16) inch outside diameter by one half (1/2) inch inside diameter.
Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
1-7/16" Firewall Grommet
p/n: 40-0204-21
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
Cowl Drain Gutter Hose Grommet
p/n: 40-0202-54
Grommet, cowl drain. One and seven sixteenths (1-7/16) inch outside diameter for seven sixteenths (7/16) inch drain hose through firewall.
Vacuum Cylinder Seal
p/n: 30-0203-24
Seals, actuating valve rod, brake and clutch vacuum cylinder.Width: .875 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Door and Trunk Handle Gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Door Handle Gasket
p/n: 40-0133-70
Pad, door handle escutcheon. Two and three fourths (2-3/4) inch by one and one fourth (1-1/4) inch.Width: 2.75 inches. Height: 1.25 inches.
Door Bumper
p/n: 40-0010-70
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.
Roof Insert Seal
p/n: 20-0102-45
Seal, top insert for closed cars without turret top. Fits groove between cloth top center panel and steel surround. Available by the foot.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Rear Spring Thrust Washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Door Weatherstrip
p/n: 40-0487-73
This Door Weatherstrip is made of a high-quality dense rubber. The weatherstrips is commonly used as a bottom door weatherstrip but can be for a variety of uses. Available by the foot.
11/16" Channel Filler Weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel. Available by the foot.
3/4" Windshield Weatherstrip
p/n: 40-0015-52
This Windshield Weatherstrip has a three eighths (3/8) inch wide opening and one eighth (1/8) inch diameter retaining bead, for metal frame around glass. Available by the foot.