Window Pinchweld Seal
p/n: 20-1882-52
Seal, garnish molding to dash rubber. Eighty four (84) inches long. Replaces factory #B7A-7003127-E.
Cowl Ventilator Grille Weatherstrips
p/n: 20-1886-54
These Cowl Ventilator Grille Weatherstrips are used to reduce noise from the cowl top ventilator grille. These U-Shaped stripes are designed for a superior fitment and seal.
Door Handle Gasket Set
p/n: 20-1936-69
Pads or gaskets for the outside door handles. Front or rear, this is a four (4) piece set.
Window Sash Channel
p/n: 20-1909-62
This Window Sash Channel is designed from the original part for superior fitment and seal. Thirty-four and three-fourths (34-3/4") inch long EPDM rubber extrusion that goes between glass and metal sash lift channel. One (1) roll required per window.
Window Pinchweld Seal
p/n: 20-1881-52
Seal, garnish molding to dash rubber. Forty six (46) inches long. Models WITH A/C. Replaces factory #B7A-7003127-B.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Main Wiring Loom Grommet
p/n: 20-1811-20
This Main Wiring Loom Grommet is used to run the main wiring loom to the firewall without being damaged by sheet metal. Designed from original part so it fits correctly.
Ventilator Air Inlet Duct Door Gaskets
p/n: 20-1827-31
This Ventilator Air Inlet Duct Door Gasket pair is designed from the original part for superior fitment and seal. These gaskets seal between the ventilator air inlet duct door to the duct inside.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Front Fender Pads
p/n: 20-1866-45
This Front Fender Pad pair is designed from the original part for superior fitment and seal. These weatherstrip pads fit at the top rear of the front fender to cowl panel.
Glovebox or Fuel Tank Filler Door Bumpers
p/n: 20-1220-88
This Glovebox or Fuel Tank Filler Door Bumper pair is a quality reproduction of the original factory part. This push on rubber bumper attaches to support / cushion the glovebox or filler door closure.
Wiring grommet
p/n: 20-1801-17
Grommet, license plate light wire. Installs where wire comes in rear bottom of trunk.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Accelerator Pedal Rod Seal
p/n: 20-1448-41
This Accelerator Pedal Rod Seal is used to run the pedal linkage to the firewall. Designed from original part so it fits correctly.
Clutch or Brake Pedal Bumper
p/n: 20-1051-24
This Clutch or Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a clutch or brake pedal arm stop cushion.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.