Spring Shackle Bushing Set
p/n: 20-2481-33
This Spring Shackle Bushing Set is for the front of the rear leaf spring. Two (2) kits required per car.
Steering Column Lower Flange Insulator
p/n: 20-1532-88
This Steering Column Lower Flange Insulator is designed from the original part for superior fitment and function. This insulator fits around the lower steering column inside the vehicle to prevent metal to metal contact.
Taillight Lens Gaskets
p/n: 20-1229-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens and taillight housing bezel.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Air ventilator seal
p/n: 20-2967-31
Grommet, air ventilator duct cable to firewall.Qty Required:2 Two (2) required per car.
Gravel shield bumper
p/n: 20-2956-28
Pads, front stone deflector to bumper arm anti-rattler. One (1) required per car.
Fresh Air Gasket
p/n: 20-2962-31
Seal, radiator air deflector to top of radiator. Twenty (20) inches long.
Front Bumper Grommet
p/n: 20-2507-45
Grommets, front stone deflector to bumper arm anti-rattler. Four and one half (4-1/2) inch long. Two (2) piece set.
Radiator Shroud Seal
p/n: 20-0182-31
Seal, radiator side air deflector. One and five eighths (1-5/8) inch by twelve and one half (12-1/2) inch.
Radiator Stone Deflector Seal
p/n: 20-2954-28
Seal, front stone deflector to radiator. Nineteen and three fourths (19-3/4) inches long.
Ventilator Air Valve Gaskets
p/n: 20-2966-31
This Ventilator Air Valve Gasket pair is designed from the original part for superior fitment and seal.
Hood bumper
p/n: 70-2871-42
Bumper, hood, front adjustable. Bumper threads into radiator support on left and right side. Two (2) required per car.
Main Wiring Loom Grommet
p/n: 20-1811-20
This Main Wiring Loom Grommet is used to run the main wiring loom to the firewall without being damaged by sheet metal. Designed from original part so it fits correctly.
Ventilator Air Inlet Duct Door Gaskets
p/n: 20-1827-31
This Ventilator Air Inlet Duct Door Gasket pair is designed from the original part for superior fitment and seal. These gaskets seal between the ventilator air inlet duct door to the duct inside.
Overdrive Cable Grommet
p/n: 20-1812-20
This Overdrive Cable Grommet is used to help protect the overdrive pull cable when passing through the sheet metal of the firewall.
Headlight Bucket To Fender Gasket
p/n: 20-1542-14
This Headlight Bucket To Fender Gasket is designed from the original part for superior fitment and seal. These gasket fits the headlight bucket and front fender.
Antenna to Front Fender Mount Pad
p/n: 20-1809-19
This Antenna to Front Fender Mount Pad is a high-quality reproduction of the original factory part. This mount pad installs between the antenna mounting base and top of front fender to protect the painted surface.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Hood bumper
p/n: 70-2876-42
Bumper, hood adjustable, rear. Slip-over rubber cover for threaded stud that mounts on both sides of cowl.
Rear Spring Pad
p/n: 20-1275-32
This Rear Spring Pad is used as a spring insert silencer. The leaf spring insulator installs between the leaves.
Front Fender Pads
p/n: 20-1866-45
This Front Fender Pad pair is designed from the original part for superior fitment and seal. These weatherstrip pads fit at the top rear of the front fender to cowl panel.
Glovebox or Fuel Tank Filler Door Bumpers
p/n: 20-1220-88
This Glovebox or Fuel Tank Filler Door Bumper pair is a quality reproduction of the original factory part. This push on rubber bumper attaches to support / cushion the glovebox or filler door closure.
Wiper Transmission Gasket
p/n: 20-1884-53
Gaskets, wiper pivot bezel to cowl. Replaces factory #B9A-17541.
Wiring grommet
p/n: 20-1801-17
Grommet, license plate light wire. Installs where wire comes in rear bottom of trunk.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Accelerator Pedal Rod Seal
p/n: 20-1448-41
This Accelerator Pedal Rod Seal is used to run the pedal linkage to the firewall. Designed from original part so it fits correctly.
Clutch or Brake Pedal Bumper
p/n: 20-1051-24
This Clutch or Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a clutch or brake pedal arm stop cushion.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.